Having problems with your Roomba Robotic Floor Bagless Vacuum ?

I cant get the brush to fit back into my roomba

\015 I have taken out the brush before for cleaning and always have a very hard time putting it back in. what am i doing wrong? is there a diagram or method you could give me?\015

Answers :

I had the same problem, but I cleaned out the hello brush bearing on the end and was able to fit the brushes back in. Apparently, enough little hairs got underneath it to push it out. This video shows you how to clean the brushes and shows you how to clean out the bearings around the 1:10 mark. Hopefully this helps.
http://homesupport.irobot.com/app/answers/detail/a_id/740/p/788
Repair Help & Product Troubleshooting for Roomba Robotic Floor Bagless Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cant get the brush to fit back into my roomba


I had the same problem, but I cleaned out the hello brush bearing on the end and was able to fit the brushes back in. Apparently, enough little hairs got underneath it to push it out. This video shows you how to clean the brushes and shows you how ... Roomba Robotic Floor Bagless Vacuum

Cant get brushes back in roomba - Vacuums


... Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!


Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!


... Roomba Robotic Floor Bagless Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

CANT GET MY POWERSTEAMER PRO DELUXE MODEL 8804 BACK TOGETHER


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL


... Bissell 1200A SpotBot Pet Robotic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I took the brush out to clean it and cannot get it fitted back in. I need a diagram to ut it back together


May I get the make and model # of the vac to help you more. ... Miele S514 Solaris Electro Plus Vacuum

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?


Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tried to take roller brush out to clean it's housing, cant get one side back in without trying to force it.


The roller brush fits snug in the housing, however, if you had it out, check to make sure the end caps of the brush shaft are pushed all the way on. These just slide on the roller bar shaft and if something got under them, they would not be able to ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My roomba spins and moves back and after 2-3 minutes stops and makes the uh oh sound followed by 10-12 beeps I cant say Im sure how many. Some days before stopped cleaning and told me to remove and clean the brushes I did that but then had this problem


\015\012\015\012\015\012\015\012Your bump sensors are malfunctioning. I had the same problem.. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend it. ... iRobot Roomba 530 Robotic Vacuum

I cant get the belt and roller back on


... Riccar 8955 Upright Vacuum

Roomba discovery My roomba comes off the charger and will go about a minute and a half. Then it will stop and beep once. i checked roombas sight and they said that the brushed need to be cleaned. I cleaned the brushes 6 times. It still does the same thing. I bought it from you in November of 2007. Should I bring it back to your service department?


Greetings doreen f,\015\012\015\012The roomba unit carries a one year manufacturers warranty, so you should be able to bring it into your local Best Buy™ store and have them try to repair it. \015\012\015\012I hope this ... Roomba Robotic Floor Bagless Vacuum

My roomba keeps telling me "error and to clean the brushes. I have cleaned the brushes and when I turn the roomba back on it keeps clicking underneath the roomba. I'm not sure what else to do.


I had the identical problem. I cleaned the brush but the problem persisted. I then put in a new brush that was provided in the box and the problem vanished. I have since used the cleaning tool on the old brush and will try and reinstall it to see ... iRobot 4150 Roomba Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net


What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

My husband took the brush and base assembly apart to clean the unit...when he took the wheel assembly off the small white leveller inside fell off. How do we get this back on??


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a roomba 530 pet series. It appears that the brushes aren't turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn't get pushed into the bin.


The belt either broke or has come off the track.... this should be easily accessable from the underside of vaccuum ... iRobot Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Brushes won't fix back into holder without being forced, so Roomba clicks when it runs. It will only run a little while and then stop and say to clean Roomba's brushes.


It sounds like you didn't clean the bearings. On one end of each brush is a bearing, probably in a yellow housing. Pull the bearing off the axle, and you'll find it's full of hair underneath.Obviously, the brushes should turn freely and s ... Roomba Vacuums

Cant get the bottom plate back onto my dyson upright DCO7i


You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums

I HAVE A DC33 BRAND NEW DYSON I EMPTIED TO CANISTER AND NOW CAN NOT GET IT BACK ON FOR A GOOD FIT TO GET SUCTION


... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

I took the filter assembly apart, now I can't get it back together. There's a silver medal ring, a big cotton back, an inner plastic seal and an outer plastic seal. Somehow, they all fit back together. It's not in the factory manual. Nilfisk GS 90 Cannister.


The cotton bag wraps around the hepa filter - the blue plastic part will not be visible once the bag is in place. The silver ring sits inside the cotton bag to hold the sides of the bag against the sides of the vacuum top-half. DON'T pull the plastic ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0707 seconds