Having problems with your Royal Brush Roll H/C 501 503 ?

Installing belt for royal 501 belt - Royal Brush Roll H/C 501 503

Answers :

Watch this video for instructions
Repair Help & Product Troubleshooting for Royal Brush Roll H/C 501 503

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Installing belt for royal 501 belt - Royal Brush Roll H/C 501 503

Watch this video for instructions ... Royal Brush Roll H/C 501 503

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The small belt attached to the roll brush keeps slipping off. It's a brand new belt and the vacuum is only 1 yr old.

The small belt rarely gives the problem you describe. The larger belt can jump off if the belt is worn or if th roller gets caught on something suddenly.The belt should be replaced every 9 - 12 months. If your carpet setting is too low this will caus ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher

If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Brush Roll belt won't engage on WindTunnel self-propelled

When you had the brush roll off, did the ends turn freely? If not then the brush won't turn and the belt will just slip. You would have to replace the brush roll if either of the ends are frozen. Other then that you would have to remove the top co ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.

The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the

... Dirt Devil M088905 Vision Bagless Upright Vacuum

Hoover U6434-900 Brush roll not spinning, has new belt.

I took the top of the vacuum apart and found the cable that drives the wheels was broken. I am going to order a new cable. ... Hoover U6434-900 Bagged Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?

... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

How to instal a new belt for the brush of the bissell ProHeat

Need to install belts ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replacement belt for rolling brush attachment

... Vacuums

How to install drive belt on SEB 204 power brush for miele s324i

... Vacuums

Replace belt nimble brush roll

... Electrolux Vacuums

Brush is not rolling. I have checked the belts

Unhook the belt see if the motor shaft turns by itself. If it doesn't then the motor is the issue. If it runs then its probably the belt or the brush roll. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0721 seconds