Having problems with your Royal M1030Z Bagged Upright Vacuum ?
What is the part number for the belt on a Royal M1030Z Vacuum cleaner
Repair Help & Product Troubleshooting for Royal M1030Z Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
What is the part number for the belt on a Royal M1030Z Vacuum cleaner
... Royal M1030Z Bagged Upright Vacuum
I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum
I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.
You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums
The foot pedal on my Kenmore upright vacuum cleaner has broken three times. The vacuum model number is 116.33923 and the Sear's part number is 8174906. Does Sears make this part in metal instead of plastic? It is becoming expensive to keep replacing this piece when it costs around $20 each time (including shipping) Thank you for your time. Jerry DeWulf
The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.
... Panasonic MC-V7515 Bagged Upright Vacuum
Where can I get a complete factory list of parts numbers for the Bissell 3750 Series Bagless Vacuum Cleaner. I found an exploded diagram but parts did not have official part numbers listed.
If in Australia call godfreys vacumm they can probably email one to you or look up www.bissel.com and ask them ... Bissell Vacuums
I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo
Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum
We own an ElecktaPure Exclusive Edition EP-4000 cannister vacuum cleaner and we are having a heck of a time trying to find replacement bags for it. We could not find the original part number of a suitable replacement part number. Can you help?
... ElektraPure Vacuums
A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.
If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
How do I change the belt on my Hoover Elite Dual Purpose Vacuum cleaner? The belt part # is 38528-027. Where is the motor pulley?
The hoover belt number you listed (38528027) has been changed by Hoover to 38528040. Below I have listed a link to the manual that has instructions and a link to the belt you need. Hope this helps! ... Hoover Elite U5061-900 Bagged Upright Vacuum
I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check
I bought a Clean Broom Electric Co., Model #CBU_5 (SKU# 7986628) Vacuum Cleaner 31CX E 255344. I have need of the following parts 2 belts and brush bearing seals. How do I locate these parts or to find them to purchase them. Thank you for any assistance you can give Tom Freer [email protected] Manufacture Date 0906
I need a screw on filter for model cb9191j-10a vacuum from clean broom electric company. ... Vacuums
Pullman vacuum cleaner parts belt for pu3 - Vacuums
Eureka vacuum cleaner 6982a has a curcit board with a switch. is this replaceable and a part number
... Eureka 6982 Bagged Canister Vacuum
Hoover belt 38528 is broken where can we find the replacement part and how can I install it again? or is there a place to get service for this vacuum cleaner?
Try your local yellow pages and see if there's a vacuum shop around your area. If so, they will be able to help you with a replacement belt and assist you on putting it on.Most vacuum shops carry parts for Hoover and will service the vacu ... Hoover Tempo Widepath Upright Vacuum - Blue
What is the correct part number for a belt for Eureka 5071F model self prop vacuum
... Eureka Vacuums
I have model a Riccar 8905 upright vacuum cleaner. When changing the belt a part fell out and I don't know where to put it or what it does.
... Riccar Vacuums
I have a Kenmore vacuum cleaner model 37010 and I have a problem with Cup container part number is 2374120000. I wonder if you can tell me where can I find this.Thanks.
... Kenmore 37010 Upright Vacuum
I need a belt for my Shark Pursuit Euro-Pro X vacuum. What is the part number and where do you get one?
I am unsure of the part number, but they have them for about $5 after shipping here:http://www.totalvac.com/accessory/parts/sharkbelt.html ... Euro-Pro UV209 Upright Vacuum
My girlfriend has a Hoover upright vacuum, Mdl. # U4645-930. I need a belt for the brush and a new bulb and am having trouble finding the correct part numbers so I can pick one up locally. Can you help?
I checked with Hoover and they said the part number for the belt is #38528040, for the bulb #27313101, and they also included a part number for something called an agitator #48414081. Not sure if this is required to replace one of the other parts. ... Hoover Windtunnel Turbo Power U4645-930 Vacuum
Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced
There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum
Hello I have a hoover vacuum cleaner, it's an older one model number 44535830.....I bought a new belt but have no idea how to put it on? can you help me
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542810\015\012Generic problem for all Vacuums\015\012Hello I have a Hoover\015\012Posted by rrunner ... Vacuums
What is belt part number foe bissell 3108 - Bissell 3108 EasyVac Powerbrush Upright Vacuum
The drive belt part number is 210-0130 for the bissell 3108. The number for bissell consumer services is 1-800-237-7691, hope this helps!! ... Bissell 3108 EasyVac Powerbrush Upright Vacuum
Hello experts. I have a Hoover u6454-900 vacuum and need new belts a thin one and a thicker one. and I do not have the manual and do not know the parts numbers for these. please please help.
... Hoover U6454-900 WindTunnel Bagged Upright Vacuum
What is the replacement part number for the belt onthe Agility upright vacuum
... Hoover UH70060 Bagless Upright Cyclonic Vacuum