Having problems with your Royal Procision 3050 Bagged Canister Vacuum ?

Royal 3050 power head does not run

\015 Smoke came from the powerhead. The powerhead will not run. There is no voltage from the canister to the hose. Vacuum still has suction. How do you get the canister apart?\015

Answers :

The sounds like powerhead motor either burned up, or the belt broke and got tangled in the turning motor shaft. Pull the bottom off the power head and look for a curled up rubber band. If you find one, it's the belt.

If it's the motor, you won't hear it running when you turn the powerhead on.
"There is no voltage from the canister to the hose. Vacuum still has suction."

That means that the motor is good.

If there is no power to the powerhead, and you got smoke, then either the powerhead motor had gone, or there had been a short in wirings.


The schematics for your model are not available on the web, you can order them by contacting one of the two websites below:


Royal Repair Parts - Hesco, Inc.

Royal Vacuum Schematic and Part Lis

Repair Help & Product Troubleshooting for Royal Procision 3050 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Royal 3050 power head does not run


The sounds like powerhead motor either burned up, or the belt broke and got tangled in the turning motor shaft. Pull the bottom off the power head and look for a curled up rubber band. If you find one, it's the belt.If it's the motor, you ... Royal Procision 3050 Bagged Canister Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run


If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

Power head has power but motor won't run


Circuit brealer switch may be bad, but the fact that Rainbow nozzle made this strange sound makes me think that it may have ha ... Rainbow E series Canister Wet/Dry Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Royal 4750 power head has no power


... Vacuums

How do you change a belt for the belt on the Royal Part #2-470010-801, Power carpet head attachment for the Royal Classic Power Team canister model #4750?


... Royal Vacuums

Power Head keeps cutting in and out while vacuuming???Canister motor keeps running but the power head starts and stops like there is a short or some loss of connection somewhere. Any ideas?


My kenmore progressive vacuum had the same problem. The electrical terminal at the bottom of the wand was corroded. I used a flat head screw driver to scrape the female portion of the connector as best as I could. I then took off the plastic cover on ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Hoover s3765 windtunnel power head does not run


I have the exact same problem as you have. Have you found a solution since you posted on Mar. 18, 2009? Thank you. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

HAVE A RC1400 THAT WON'T RUN. BELIEVE ITS THE POWER CORD BUT CAN'T GET THE VACUUM OPEN . THERE ARE FOUR DEEP HOLES IN THE CASE BOTTOM BUT WHATEVER IS IN THEM , JUST HAS A FLAT ROUND HEAD, NOT PHILLIP'S HEAD OF SLOT. J F


Should be size 15 or 20 torx bit screwdriver required ... Riccar Vacuums

Broken belt I have a royal canister model 4750 with a broken belt on the power head. I don't know how to disassemble the head to get at the belt.


If you have the power head with the headlight, squeeze the sides of the upper part (almost like a superstructure,) where the headlight is located. It should lift off, allowing access to the screws to get the powerhead apart the rest of the way, and o ... Vacuums

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?


Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

I have a Kenmore Model 116 26312603 sweeper. The vacuum motor does not run, the power head does run. What is the most likely solution?


If the switch is a simple on/off switch,it could be that.Make sure it is unplugged.If you take the switch apart,twist the two wires together,and cover with electrical tape.If you do not have electric tape,make sure the connection is off of the ground ... Vacuums

Dyson DC15 vacuem run except power head will not run


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Eureka cv1373 power head will not run


... Eureka Vacuums

Broken belt in Royal Pony power head


We have a Royal Pony as well. Here is their general help desk number. Just call them and give them the model number of  you tank. it's on the bottom of your machine. 1.800.321.1134 ... Vacuums

My beam serenity plus power head shuts off as soon as it hits our carpet. It runs when held off the floor though. Do you know what could be causing this? The only thing that starts it up is the red reset button.


... Beam Industries 2900 Serenity Plus Central System Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.


Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.


I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Shark S3501 Steamer. No Steam Comming out. I have power,Heat but no steam.I tried all three heads to no avail. Is this like the coffee pots that you can run Vinigar (acidic acid) through to clean out the venturie?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro-Pr ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

S3755 Hoover canister bagless vac no power to head


... Hoover Vacuums

Dirt Devil M082475 12 AMP cannister vacuum power-head problem


Theres no fuse, you will need a new hose ... Bosch 12-Amp Formula Canister Vacuum with Hepa Filtration Bagged Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0405 seconds