Having problems with your Rubbermaid Reveal Spray Mop Kit, FG1M1600GRYRD ?

I bought a rubbermaid reveal mopping system.and I dropped the mop while using and the bottle fell out, the cleaning solution gurgled all over the floor, and now the cap is stuck inside the mop. Can anybody help me think of a way to get it out without damaging the unit?

Answers :

Try using a pair of needle nosed pliers, in reverse. Put the tips into the cap and SPREAD the handles. The jaws MIGHT provide enough grab to back the cap out. Otherwise, it will be a try this and try that job. No two are ever alike.
Repair Help & Product Troubleshooting for Rubbermaid Reveal Spray Mop Kit, FG1M1600GRYRD

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I bought a rubbermaid reveal mopping system.and I dropped the mop while using and the bottle fell out, the cleaning solution gurgled all over the floor, and now the cap is stuck inside the mop. Can anybody help me think of a way to get it out without damaging the unit?

Try using a pair of needle nosed pliers, in reverse. Put the tips into the cap and SPREAD the handles. The jaws MIGHT provide enough grab to back the cap out. Otherwise, it will be a try this and try that job. No two are ever alike. ... Rubbermaid Reveal Spray Mop Kit, FG1M1600GRYRD

Stuck Roller Same problem here. I think in our case, the accumulation of hair and the increasing resistance the hair created over time caused the hair to start melting, and eventually the end cap was stuck to the roller, which prevented the roller from turning. I cleaned out the melted hair(?) as best I could, but I think I need to order a new roller and end caps.

Befrore you plunk your $ down ...\015\012\015\012I dont now that you melted the hair so much as you may have an accululation of gunk and hair. If there is a good (not 'fast food' type) auto parts store near you, go there and ask the cou ... Electrolux 1910 Bagless Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I am having problems with the roller on my Oreck DTX-1300. It turns on and off intermittantly while I'm vacuuming. I have completly taken it apart and cleaned and inspected the roller unit.(I am very much mechanically inclined) This has stumped me, I have checked the electrical from the vacuum to the floor unit, and everything else that I could think of. Question: what does the metal sensore plate on the bottom of the roller unit do?? Anything anybody can tell me, I would greatly appreciate. Cap

... Oreck DutchTech DTX1300A Bagged Canister Vacuum

Oreck XL How to remove rear wheel. Removed all viewable hair, thread, etc., but one wheel is still hard to turn. I think there's hair stuck inside the wheel core. Can I remove the wheel & take it off the metal post?

You can take a medium size flathead screwdriver and slide it in beside the wheel and under the pin. Then pry carefully on one side and then the other it will start to come out but work both sides alternately so you won't put too much pressure on the ... Oreck XL2000 Bagged Upright Vacuum

My hoover is broken, the hooze doesnt **** the dirt.I emptied the bag inside, there is nothing stuck in it.I think the hooze needs to be changed, where can I do it in Dublin?

You might check to see if the hose or the dirt inlet by the brush roll for a clog. Is the brush roll turning while you vacuum? If not, you may need a new belt. They stretch after awhile and turn the brush roll under load. ... Vacuums

Hi, The dirt does not **** into the canister. It looks like the cyclone system is not working. I think something is stuck inside. How do you recommend to fix it? Thank you for all your advice. Fiona

There is no vacuum action on your set. So as you mentiioned there is little or no suction available which means that the pump is not working correct. The two possibilities are either a large block of an object inside or the failure of the vacuuum pu ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

Shark steam mop, no steam, "exploded" and wet inside?

... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b

... Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Who makes ek8005 steamleaking under cap need new cap and allparts under it.I got trhis from someone and I think parts are missingNeed picture of cap and parts.

It's made by Kable Enterprises Co Ltd - a chinese manufacturer that sells them under different made-up names. No parts are available for it - it's a "use and throw away" device. The only source for parts are other defective units kept for parts - se ... Vacuums

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.

Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

I have the scunci 1000 steamer- it was sitting for a while and the cap on the top looks like its corroded and i cannot remove it from the steamer - i just bought it a year ago, but i think the salt or vinegar from cleaning it got trapped in the top and i tried everything i could think of to loosen the top so i could pour water into the unit and use it again; otherwise it is in perfect condition, but i tried even pliers and i cannot loosen it and i dont want to break it, but am so frustrated - wh

Hi, Elaine, W/D here.Corroded items are difficult to break loose as the corrosion builds up a layer that binds the parts together. Try this, as I usually have good luck with this method:Tap around the perimeter of the cap with a wooden h ... Scunci SS1000 Handheld Steam Cleaner

Hi, A few days ago I bought a Philips hairdryer (HP4935/22) & have used it only twice. Somehow when I used it this morning some of my hair got caught in the filter at the back of the dryer & the motor slowed down & I think overheated & stopped. Normally the filters come off but I don't think this one does. I haven't turned it back on so as not to possibly damage it even more. I am quite upset as I really love this hairdryer. It's quiet, light, small, powerful & does the job brilliantly. I h

This is usually a safety feature so it doesnt burn itself. If there is a lot of hair in there try pulling it out, and if there is a little try with it too, if you can try get it out with something. If you think there isnt any in there anymore, try to ... Philips Vacuums

I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?

... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

Steam is coming out of the cap of my steam buggy which is preventing steam to build up inside the canister. The canister did fall on its side right before this happened. Why would steam be coming out of the cap?

... Tristar SB Steam Buggy Vacuum

Dyson dco5 Pulled the unit too hard to get extra flex. The plug is ok changed the fuse. I believe the cable has detached itself from the inside. How can i check the inside of the unit for cable damage

Hi.\015\012\015\012Try this site has manuals on replacing mains rewinder unit on Dc05.\015\012http://dysonmanuals.llc.nu/\015\012\015\012Chris.. ... Vacuums

Bissell steam mop is shooting the steam and some water out the side in a little hole. The water tank was left on the mop so i'm thinking the filter is plugged?

... Bissell 1867 steamMOP Stick Vacuum

Cap stuck Cold unit preparing to use and cannot remove the cap

... Euro-Pro Shark SC-505 Handheld Steam Vacuum

The child-proof-type resivoir cap is stuck, really stuck - off the grooves and will not budge. Any suggestions short of dynamite? It's a stefast mouse item sf-250.

You may have to use a large pair of channel lock pliers,and force it off,the same procedure in taking it off normally,but with channel lock pliers. ... Steam Fast Vacuums

Cap (top) is froze. Unable to remove cap (top) to pour water inside for use. not sure if model specified is correct. It's a canister with hose and multiple attachments for cleaning.

I too can not figure out how to get the lid off. ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.

Remove the cap that directs the air and insert the hose in there. ... Vacuums

I think you should look at this problem. The mop is only as good as its weakest link and that is this hose. You have an excellent product here and I think it deserves looking into. Thank you. Gary Frascone Sr. [email protected]

Go Shark and get your hose. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0489 seconds