Having problems with your Samsung Quiet Storm 9069 Vacuum ?

How do I remove cover to get to on off switch?


Answers :

The on/off switch is soldered to the circuit board which is covered by 3 plastic pieces that form "wings"..... the cord retract button and the on/off button. First remove the screw nearest to the Slider at the "MAX"position. There are 3 hooks formed on the plastic that fit into their respective detents, one under the "MAX", another under the "OFF" and the last under the "REWIND". Pull up on the On/Off wing at the point opposite the On/Off lettering. That should release the first hook. Then grab both wings on the side lateral to their respective lettering (and make a wish!) er, uh no, just pull straight up with enough sudden force to break it free. Worked for me without damaging anything. Hope that helps. I wonder what the shop manual says?I didn't try to replace the switch..... just bought a new C/B for $20. Sold at oregon city vacuum or apwagner.
Repair Help & Product Troubleshooting for Samsung Quiet Storm 9069 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove cover to get to on off switch?


The on/off switch is soldered to the circuit board which is covered by 3 plastic pieces that form "wings"..... the cord retract button and the on/off button. First remove the screw nearest to the Slider at the "MAX"position. There are 3 hooks forme ... Samsung Quiet Storm 9069 Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Eureka Vacuum Excalibur Model 6975A on/off switch won't turn off. Probably need new switch but can't figure out how to get cover off to get at switch


... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do you get to the 2 screws under the cord retraction pedal? I can not find any way to remove the pedal. I am trying toi remove the canopy cover in order to get to the motor>


What model is this for? ... Kenmore Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I have a replacement switch. How do I get the cover off to get at & replace the defective metal switch? Thanx Pete Potter


Hi, you need not to do this yourself, just take it to a electronic repairer around you to take if off and replace the defective metal rather than stress yourself...Take care ... Eureka Sanitaire S661 Bagged Upright Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.


... Kenmore Progressive Direct Drive 30912 Vacuum

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?


Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Dyson slim cannot remove switch cover


Here is video for DC07 switch replacement,http://www.videojug.com/film/how-to-replace-a-dyson-switch-and-actuator-dc07 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

Cover knobs How do you remove the two plastic knobs on the cover for bare or carpet and carpet heighth to get the cover off?


You don't have to remove those knobs to get the cover off. Just 2 screws from the bottom, then on each side you will notice a slot from the bottom, use a screwdriver, insert in the slot, and pry out to release the catches and the top cover will come ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?


... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Power switch fails to stay in ON position when pushed. I can get a replacement switch but can't figure how to remove the old switch


... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to remove the outer shell to get to the power switch


... Simplicity 7850 Premier Bagged Canister Vacuum

On/off switch not working. How do I get the plastic cover off to look at it? I think it's probably a very simple fix if I could get to it. Have to unplug it to turn it off.


Hello, my Dyson is dead, i've replaced the on/off switch with no change. To get at the switch, firstly pull off the bag/syphon box and then remove the handle. Behind the handle you will find 2 torx screws and 3 clips, when you have removed the screws ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks


Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0719 seconds