Having problems with your Sandia Sniper 6 Gallon Carpet Extractor 100 PSI Single 3 Stage Moto ?

Need wiring schematic for sandia sniper 3-200 6 gallon

\015 Mainly need to check the connections of the white wires.\015

Answers :

Repair Help & Product Troubleshooting for Sandia Sniper 6 Gallon Carpet Extractor 100 PSI Single 3 Stage Moto

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need wiring schematic for sandia sniper 3-200 6 gallon


... Sandia Sniper 6 Gallon Carpet Extractor 100 PSI Single 3 Stage Moto

Wiring Schematic I need the wiring schematics for my XL3600HH, as I am replacing the motor and did not receive the schematics. Unfortunately, I can not remember the exact wiring. Please help. Thank you


Hope this will help you. There is 4 different ways to hook it up depending on what you have,\015\012\015\012 ... Vacuums

Need wiring schematic for an Oreck XL21


... Vacuums

Need wiring schematic for ametek 119550


I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. T ... Vacuums

Need Bissel 1719 series, 1718 series wiring schematic. Charging circuit has burnt resistor. Need to know resistor details


... Vacuums

Need Bissel 1715 wiring schematic. Charging circuit has burnt resistor. Need to know resistor details.


Can not believe NO ONE could answer this. \015\012\015\012The R1 resistor basically drops the 9V to around 5V for charging the battery pack. The resistor is a 10 ohm , 2 watt resistor. The other resistor is 220 ohm. This only limits the c ... Bissell 1715-G Spotlifter Bagless Handheld Vacuum

I need the wiring schematics for my fantom twister fm760k vacuum i am fixing something on my motor and didnt receive the schematics. thank you. fay


... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Wiring Schematices Hello, Thank you for posting the wiring schematics on FixYa. Those are the ones I needed. However, I cannot make them out on the webpage. So, if you could kindly send me a copy to my e-mail address, it would b highly appreciated. Prefferably in .pdf format if possible. Thank you very much. Desperate To Repair Kent


I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. T ... Oreck XL Ultra Bagged Upright Vacuum

I restored my Eskimo fan and its not turning on? I think I just have one of the wires wrong. I just need the schematics to it to check that I wired it right.


... Vacuums

I need a wiring schematics for my ezi-vac 2(euroclean) please.


Thanks for getting back to me,i solved the problem by asking a vac tech and he told me what to do ,it was easy.cheers gazza. ... Electrolux Vacuums

Rplacement part I need the part # or a schematic so I can determine the part # for the little black cylinder with 4 wires sticking out of it that commects the power cord to the two motors.


Http://www.oreck.com/customer-service/owners-guides.cfm#Her is the oreck manuals web page.They can also tell you where to get parts. ... Oreck XLS700A Upright Vacuum

Need wiring schematic for Oreck model # U3700HHA


... Oreck XL Deluxe U3700 Bagged Upright Vacuum

DO YOU HAVE A WIRING SCHEMATIC FOR A KENMORE CANISTER VAC MODEL# 116 22600200C? I NEED TO TRACE BACK A PROBLEM, THANKS


... Kenmore 25512/ 25513 Progressive Canister Vacuum

I need a wiring schematic for on/off switch on my Kenmore model 116.25512 vacuum.


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Need wiring schematic for Filter Queen MD#31X.


... Vacuums

I bought a new motor for my Riccar 8850. The new motor has 3 wires and the old one has 2. Which color wire is the ground? (or, which color wire don't I need?)


The third wire is a hot wire that goes to the headlight. ... Riccar 8850 Vacuum

Need a wiring diagram for a karcher puzi 100 yellow. Mainly need to know which way round the wires go on the switches?


... Vacuums

Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.


Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums

Need proper wiring connections inside unit, where they have pulled apart from squeeze connectors.(Wiring diagram needed) Can someone E-Mail this to me? Fritz (an ''old'' mechanic) Folks I have talked to, say there is no specific model number for these units. They are just described by name, and serial #. and I have relayed exactly what was labled on the unit. Please post this and quit asking me to enter a "valid" product.


Fritz , thanks please confirm... there are likely more than 2 leads from the motor?? I have not seen or worked on the Tristar CXL as it is very new.You will have a high low function but: Should the power head function at both spee ... Vacuums

I took my durabrand toaster oven model t0-80 apart and i need the wire diagram to put wires back on it cause it needed cleaning.


... Vacuums

Wireing schematic for Bissell vacuume cleaner#3760-4


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Wiring Schematic Hello, Did you ever receive the wiring schematics for your Oreck vacuum? If so, could you frward them to me, as I have the exact same problem. Thank you.


\015\012\015\012Should ... Oreck XL Ultra Bagged Upright Vacuum

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0454 seconds