Having problems with your Sebo Air Belt K2 Bagged Canister Vacuum ?

My sebo airbelt k2 won't start

\015 It worked on Tues according to my cleaning woman but 4 days later is just dead. replaced bag, any suggestions?\015

Answers :

Hi\015\012It could be two things = one problem is that the cord in Sebo's K model has a bad habit of shearing thanks to its auto pull rewind mechanism. This would have to be replaced by a Sebo repairer. \015\012
\015\012Or it could be the actual electric socket if the bonded plug is loose - if there are wires visible at the end of the plug then the plug would have to be replaced. Its a common fault on Sebo's K models when the power stops thanks to shearing cords.
Repair Help & Product Troubleshooting for Sebo Air Belt K2 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My sebo airbelt k2 won't start


Hi\015\012It could be two things = one problem is that the cord in Sebo's K model has a bad habit of shearing thanks to its auto pull rewind mechanism. This would have to be replaced by a Sebo repairer. \015\012\015\012Or it could be the actual ... Sebo Air Belt K2 Bagged Canister Vacuum

Taking off the bumper from A Sebo K1 Airbelt - Sebo K1 airbelt Bagged Canister Vacuum


First, remove the clip at the back of the machine where the airbelt joins (lever it off carefully with a screwdriver). The airbelt is in two parts - the bulky foam strip and a thin material cover. The cover is held in grooves, top and botto ... Sebo K1 airbelt Bagged Canister Vacuum

Sebo Airbelt C2 Cable jammed


Take off the strip that runs around it, then you can get to the casing clips, remove them and the 2 halves come apart. ... Vacuums

My Sebo automatic X1 has stopped working Every time I attempt to switch it on the only thing that happens is the bag and roller warning lights flash briefly. This suggests the power is ok but the Sebo doesn't start. Any suggestions?


Check for clogs, and also check the brush rollers' belt.Really, i think you should take it to a vacuum shop and have it inspected for problems ... Sebo Automatic X1 Bagged Upright Vacuum

As you turn the Sebo on, the 2 red lights flash once and there is no motor. If you rotate the brush roller the motor starts. We've taken off the brush roller and put it back on and now it doesn't even start when you rotate the roller.


... Sebo Automatic X1 Bagged Upright Vacuum

Airbelt k1 komfort 2100 cylinder spool - Sebo K1 airbelt Bagged Canister Vacuum


... Sebo K1 airbelt Bagged Canister Vacuum

Cord reel for sebo airbelt d - Sebo Air Belt K2 Bagged Canister Vacuum


... Sebo Air Belt K2 Bagged Canister Vacuum

Sebo airbelt k1


No screws under the castors. There is 3 case clips, the bumper hides them, maybe this picture will help:\015\012\015\012 ... Sebo Air Belt C3.1 Bagged Canister Vacuum

My Sebo AirBelt K1 just stopped working


I work with a Sebo dealer (in the UK), where we repair all makes of vacuum cleaner. It's testimony to the quality of Sebos that in several years I've only had one of this model to repair (so my memory is somewhat sketchy). \015\012However, from first ... Sebo K1 airbelt Bagged Canister Vacuum

Sebo Airbelt K1 Electrical Problem


Remove the belt or seal that goes around it, there are some clips to take out, then it will separate.\015\012\015\012 ... Sebo Air Belt C2.1 Bagged Canister Vacuum

On my Sebo Airbelt C3, I can't open the dust bag compartment. It's jammed shut. The handle doesn't seem to be able to shift the mechanism inside.


Try spraying some furniture polish into the release handle. maybe just dust preventing it from opening and the wax and get in there and clean out the dust. Other then that, you will have to just keep working it until it opens. ... Vacuums

SEBO airbelt K3 retractable cord won't retract


... Sebo Air belt K3 Bagged Canister Vacuum

It's a sebo x1 and the motor won't start but the


... Vacuums

My sebo x4 extra does not start. There is power but no warning lights are flashing. When I turn the vacuum on there is a continual clicking/buzzing sound.


Hi.Eeither motor or servo motor with gear box is seized. Testing is done energizing the motor. Test and repair must be done by a technician. Call the number listed on the owners manual to contact a qualified repairer.See: ... Sebo X4 Bagged Upright Vacuum

How to access the motor - Sebo K1 airbelt Bagged Canister Vacuum


OK, but be warned... it's not so difficult getting the thing apart, but making a neat job of reassembly has been known to drive grown men to despair. And that's because you have to remove the airbelt. But first things first:1. remov ... Sebo K1 airbelt Bagged Canister Vacuum

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?


... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth


Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo starts and immediately stops with 2 red lights come . There are no blockages


... Sebo X4 Bagged Upright Vacuum

Changing sebo telescopic slide button, how to


Go to :http://www.sebo.co.uk/support/downloads/download your instruction manual, and proceed according with common sense forchange your parts.God bless you ... Vacuums

Sebo X4 stuck in lowest position


... Sebo Automatic X4 Blue

SEBO Automatic X1 not operating.


... Vacuums

Once again having vacuum problems, when I push the start red paddle it hesitates and won't fully starts. It makes the noice to start but then it shuts off. Makes noise to start but then promply


... Eureka 4700A Maxima Bagless Upright Vacuum

Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????


This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to "on." (If you're not sure whether it's on or off, just click it back ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.


If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0347 seconds