Having problems with your Sebo Air belt K3 Bagged Canister Vacuum ?

The ratchet has come loose in the telescopic pipe, and so will not now stayup ? can I replace it ?


Answers :

Yes you can replace that find the manufactuer or check online for parts put the model and make
Repair Help & Product Troubleshooting for Sebo Air belt K3 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The ratchet has come loose in the telescopic pipe, and so will not now stayup ? can I replace it ?


Yes you can replace that find the manufactuer or check online for parts put the model and make ... Sebo Air belt K3 Bagged Canister Vacuum

Hi , I have an Electrolux powerplus 1800 hoover Z4492 the hose that attaches to the telescopic pipe snapped and tried to get out the grey plastic out in one bit but it snapped ..if i got another telescopic pipe would it come with the grey tube that sits in the hole to keep the hose in place ?


... Electrolux Vacuums

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

The vacuum leaks dust around the joint between the bag and the vacuum. I unlatched the bag, removed and emptied it, and replaced it. However, the vacuum still leaks dust around the joint and the bag keeps working loose. How can I make sure that the bag is securely latched so that it does not leak or come loose? I have no manual. Thanks.


... Bissell 3065 Power Partner Vacuum

I removed the filter from its compartment in the base of the vacuum. There are two strips inside the compartment that seem to be coming loose and that obstruct the new filter as I try to replace it. How do I fix this?


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Airvac vm458 had to replace powerhead and telescopic wand last year and problem again loosing power shorting out and isn't working like bought it


... Airvac 14-inch Deluxe Power Brush w/ Headlight VM458

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have Dyson DC05. The plastic clip from handle to the metal pipe is broken. Can this be repaired or do I need to replace the whole metal pipe section? If so where can I do this.


Dear Madam/SirThis is very simple problem. the problem can be solved in a very simple manner.As you have told me that the plastic grip from the handle to the metal pipe is broken.You Can do it near by any welding s ... Dyson Vacuums

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.


... Sebo X4 Bagged Upright Vacuum

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?


Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Want to replace connection pipe part #KC92PBZTZV06 that goes into the cannister. Want to seperate it from adapter #4370325 without breaking it. I have the new connection pipe.


... Kenmore Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?


... Miele SEB 213-2 Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.


HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Replaced cord reel in Electrolux Epic 6000 series and the tempurature light comes on and vacuum will not come on. What is the problem?


1) see the schematic attached: and proceed according. God bless you ... Electrolux Lux 7000 Bagged Canister Vacuum

Replacement parts where can i find replacement steam pocket towels online for the shark ultra steam blaster hard surface cleaner? I went online to www.sharkcompany.com & www.sharkvac.com and when I enter my model number S3325 search comes back with 0. Thanks


You can found them on amazon, take a look here: Amazon com Euro Pro S3325. I hope this was helpful. Cheers ... Euro-Pro S3325 Handheld Steam Vacuum

How do you disassemble Rainbow D4c to replace power cord? Took four screws loose but unable to see how to get housing loose...


Gently pull on the rubber gasket that seals the water tank to the canister. Although there are more screws under there - they aren't necessary to remove only to replace your cord. It is the gasket that is holding the motor flange and the plastic hou ... Rainbow 75th Anniversary Canister Vacuum

Hoover wiring the blue wire that is in the lead that runs from the hoover to the plug that goes in the wall has come loose at the hoover end and has come out of the actual hoover. i've unscrewed it but am unsure as to where the blue lead (bare copper) needs to be screwed... if you see what i mean?!!


Hello lukeplayer,\015\012Based on your description, ( first disconnect the plug from the wall recptacle).You will need to open up the Hoover Vacuum Body to gaion access to the internal wiring. In order to better assist you, please provide me wi ... Hoover Vacuums

How do I replace the Powercord on a Fantom XT64K Vacuum. The powercord shorted where is comes out of teh housing. I need to open up the unit & replace but need a service manual of instructions. Thanks Father Lenny


I have done this several times, it's some what simple just take the unit apart and use the old diogram to replace the new one. Or take a digital photo of it opened so you have your own scematic. You should be able to purchess the cord at your local h ... Vacuums

I just replaced the belt on my Kirby Heritage II, and it keeps coming off. It is engaged when I check it, but as soon as I start vacuuming, it comes off?!


You got the wrong size. ... Kirby Heritage II Vacuum

Burning smell coming out while using a Hoover's upright vaccum cleaner (model U6434900). Replaced both flat and v-belt. The problem appears to be coming from near the motor area. The manual does not provide any information on how to reach that area. Any help will be appreciated.


Took it to a manufacturer's repair center. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.


I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums

There is an "exhaust" pipe of sorts in the lower back part of the vaccuum. Most of the dust and specially pet hair just flies out of there and up in the air. It looks like more stuff comes out than stays in the vaccuum. I'm wondering if there should be something connected to that pipe? Vacuum assembled as per instructions out of the box (installing handle).


Something is wrong ... there should not be any dirt coming out as you describe ...\015\012\015\012I'm sorry, based on what you have told me ... I can't go further ... you know ... stuff link make and model.\015\012\015\012Than ... Vacuums

BELT TO THE BRUSH SEEMS TOO LOOSE EVEN WHEN REPLACED


Hoover U6437-900 U6439-900 Upright\015\012LOOSE BELT. THE BELT IS STILL LOOSE EVEN AFTER REPLACING\015\012\015\012I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0568 seconds