Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

I need to replace the motor on a Sebo Automatic X!

\015 I cannot find how to get to the motor although I seem to have taken all the visible screws out.\015

Answers :

OK, here goes...  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine.\015\012
\015\012STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!\015\012
\015\012STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS.  All the surface-mounted screws are irrelevant to this job.\015\012
\015\012STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum tubes out of vertical.  The top cover will then lift off.  You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the right of that double pulley is the electronic circuit board - note that it has a sensor that locates within the pulley device, be careful not to damage it.\015\012
\015\012STEP 4. At the left end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back.  Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.\015\012
\015\012STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). You need to do that because the front of the motor cover is tucked underneath it, but you don't need to move the circuit board more than a few millimeters.  Then undo the four screws holding the motor cover and lift the cover away.  The motor will then just lift out.\015\012
\015\012Re-assembly is simply the reverse of the above process.\015\012
\015\012If you need more help, just ask.  Please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to replace the motor on a Sebo Automatic X!


OK, here goes...  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine.\015\012\015\012STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compar ... Sebo Automatic X1 Bagged Upright Vacuum

My Sebo Felix ET1 has a burning smell, have checked there are no blockages, could it be the motor brushes need replacing, if so how do I do this? Thanks, R.Stevens


... Sebo ET-1 Bagged Upright Vacuum

Hi, I've just had my Sebo X4 back from being repaired (motor was growling so Sebo replaced it FOC under warranty) however, the replacement motor is 1000 watts. I queried this with Sebo, as they c


Watt= volts x amps So what are you losing? Not much really. Should they replace it with the same motor? Possibly, but you got a free motor out of them. To be honest I think you're splitting hairs on this one. The difference in how much cleaning that ... Sebo X4 Bagged Upright Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.


You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram


... Vacuums

Replacing a belt on a Sebo Automatic X1 vacuum cleaner


The roller brush has stopped turning, I think it could be the belt, how do I seperate the top from the bottom?\015\012\015\012I will await your reply.\015\012\015\012Thankyou Val\015\012 ... Sebo Automatic X1 Bagged Upright Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.


... Sebo X4 Bagged Upright Vacuum

I have a kenmore canister model number 116.2645083 I need a replacement motor. I was given 2 different numbers: 1. 4147248 2. AC92FAUX200 I can find the 2nd motor, but it doesnt have the 4 wires like the original one. Can you tell me if this is the right motor? Thanks Becky


Greetings from GoVcauum.com,\015\012\015\012Ok, so good news, I have looked up your model number for your Kenmore vacuum and found that your Kenhmore canister takes the motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My riccar rc1100 needs a new motor. motor is a daewoo and the armature is now bad causing sparking. how can i get a replacement motor?


You can purchase one from www.acevacuums.com ... Riccar RC1100 Compact Vacuum

Need wiring diagram for riccar supralite vacuum, replacing motor, old motor has two wires, new motor has three


... Riccar Liteweight & RSL1A RSL3 RSL4 RSL3C vacuum bags 6pk

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?


If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.\015\012\015\012 ... M&S Systems Vacuums

Sebo automatic X1. After switching on the motor


As sure as possible without actually seeing your machine, the carbon brushes on the motor are worn out. They are quite easy to replace (and not expensive). If you need help with doing the job, just post a reply here and I'll guide you as best I can. ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo Automatic X1 cleaner, toothed belt replacement


OK, here goes... (there may be more detail here than you need, but it's a copy of a solution I wrote for someone else)  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. \015\0 ... Sebo Automatic X1 Bagged Upright Vacuum

I need replacement carbon brushes for the motor. I haven't been able to find a source.


Try looking for a power tool repair shop, they usually have some brushes and can order more. I have put Hoover brushes in my Shop-Vac.\015\012 Look for some that are close to matching,( spring size,spring length, brush length). If the brushe ... Hoover Portapower C2094 Bagged Canister Vacuum

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.


From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Motor burned out need a replacement motor. Where can I buy one?


Are you sure it's the motor? I thought that was the prob w/mine when the brushes quit spinning, but it was a little clear piece of plastic\015\012 inside the middle of the handle had cracked. This piece holds the \015\012switch in place and is prob ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Do you know of anywhere I can get an electrolux repair manual for the 1205 model - I need to replace a motor. I have the motor Arthur Gaucher


Don't buy an Electrolux.......... play their one sided game! ... Electrolux Vacuums

Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

<2 year old Eureka 4870DT with strange noise and aweful smell from motor. Roller also not rotating. The belt is intact and all tubes are clear. Do I need to replace the motor?


The price of vacuums these days are falling all the time - esp on EBay. This sounds like there's a foreign object or simply dust which has managed to get into the motor thus causing the burning smell or that the roller brush fly wheel is loose and ca ... Vacuums

When I turn on my Eureka Smartvac 4870 is the light blinks sporadically and smells like the motor is burning. How can I tell if the motor needs to be replaced?


Hello. If the motor is running smoothly and the only symptom of a problem is that the light blinks sporadically I would inspect the wiring to the light. It may have a loose connection, or a burned insulation which is causing the burning smell. Onc ... Eureka Smartvac 4870 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0923 seconds