Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

How to replace a belt - Sebo Automatic X1 Bagged Upright Vacuum


Answers :

OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed belts2_bing.gif, it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years.
STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!
STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS. All the surface-mounted screws are irrelevant to this job.
STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum2_bing.gif tubes out of vertical. The top cover will then lift off. You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the right of that double pulley is the electroniccircuit board2_bing.gif - note that it has a sensor that locates within the pulley device, be careful not to damage it.
STEP 4. At the left end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back. Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.
STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). Then undo the four screws holding the double pulley. Once that's free, you'll be able to change the belts.
Re-assembly is simply the reverse of the above process.
If you need more help, just ask. Please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to replace a belt - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed ... Sebo Automatic X1 Bagged Upright Vacuum

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??


... Bissell 3510 PowerPartner Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

How to replace belt on a eureka boss vacuum - Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum


If you look on the base plate you should see a diagram of how to do it,but if yours don't have a diagram then remove the screws from the base plate it should be three or four they have arrows next to them. take the base plate off and remove the brush ... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

Replacing belts on U3109 hoover vacuum - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

How to replace the vacuum belt - Miele S7210 Bagged Upright Vacuum


... Miele S7210 Bagged Upright Vacuum

1.1 sebo hard to push - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

Sebo Automatic x4 re-attach Foot Pedal - Sebo X4 Bagged Upright Vacuum


... Sebo X4 Bagged Upright Vacuum

Replacing belt on vacuum cleaner - Sharp Twin Energy EC-T2840 Bagged Upright Vacuum


... Sharp Twin Energy EC-T2840 Bagged Upright Vacuum

How to replace a dust bag holder on a hoover - Sebo X4 Extra Bagged Upright Vacuum


... Sebo X4 Extra Bagged Upright Vacuum

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Replacing a belt on a Sebo Automatic X1 vacuum cleaner


The roller brush has stopped turning, I think it could be the belt, how do I seperate the top from the bottom?\015\012\015\012I will await your reply.\015\012\015\012Thankyou Val\015\012 ... Sebo Automatic X1 Bagged Upright Vacuum

How do i replace the vacuum belt for a hoover upright, bagged, 18.0


Go to manuals.com and put in the model Follow directions in the manuelUsually only requires a screwdriver ... Hoover Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Belt replacement - Hoover U6434-900 Bagged Upright Vacuum


Your model requires (2) different belts. Here is a link to the belts you need and to the manual:U6434-900 Brush Roll Belt ... Hoover U6434-900 Bagged Upright Vacuum

Replaced belt but isn't tight to turn roller - Eureka Smartvac 4870 Bagged Upright Vacuum


Are you sure that you have the right replacement belt? Here is a link to the belt you should have and the manual:Eureka 4870 Belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

How do I replace a hoover windtunnel belt - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum


Here is a link to the manual and to the belts you need.\015\012\015\012\011\011\011\011\011\011U6439-900 Manual \015\012\011\011\011\011\0 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to replace my belt on my kirby g4 - Kirby G4 Bagged Upright Vacuum


Hello, amhillI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ... Kirby G4 Bagged Upright Vacuum

I have a Sanitaire model SC886 upright vacuum. It's about a year old. I replaced the belt , cleaned bag , checked for blockage in impeller fan and now it makes a noise , like a grinding noise or something . Could you tell me how to fix it ?


The bearings in the motor needs to be checked,or the impeller is damage. ... Eureka SC886 Bagged Upright Vacuum

How do u replace belt - Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum


Turn the machine over - locate the clamps that hold the cover on and open them. Fold the cover forward toward the front to expose the "belt alley". Lift the roller brush from its cradle. Place the new belt over the pulley on the brush and over the ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

I have replaced the filters and the bag on my Sebo X1 automatic upright but it still has doggy odor that I cannot seem to get rid of. What could be the cause and what can I do?


Hi, Yeah those things are fairly simple and easy to clean, My guess is that its in the hose.\015\012Try a weak solution of bleach and water, pour it in and let soak for 20 mins then rinse well. Dry it throughly in the sun before youe next use. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1457 seconds