Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

My seb0 automatic x1 roller have stopped working . there is nothing stuck in it . the suction part is working perfectly. can you help please?

Answers :

\015\012Almost certainly you've got a broken drive belt. This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years.\015\012
So, here's how to get at the belts and change them... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine.

STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!
STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS. All the surface-mounted screws are irrelevant to this job.
STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum tubes out of vertical. The top cover will then lift off. You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the right of that double pulley is the electronic circuit board - note that it has a sensor that locates within the pulley device, be careful not to damage it.
STEP 4. At the left end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back. Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.
STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). Then undo the four screws holding the double pulley. Once that's free, you'll be able to change the belts.
Re-assembly is simply the reverse of the above process.
If you need more help, just ask. Please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My seb0 automatic x1 roller have stopped working . there is nothing stuck in it . the suction part is working perfectly. can you help please?

\015\012Almost certainly you've got a broken drive belt. This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at ... Sebo Automatic X1 Bagged Upright Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!

There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Eureka 431BX suction stopped working. Roller still goes. Please help! Everything else is working great.

Even though the brush is spinning, you probably need to replace the belt\015\012because ... Eureka 431BX Bagless Upright Vacuum

Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!

Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!

The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Nothing inn the canister after using,suctione working,bottom roller working,no air leaks from hoses.Also when running awhile it shuts off by itself,have to wait awhile to use again

I'm not sure what vacuum you have, but that sounds like a blockage to me. Thermal shut off kicks in, shutting the motor down, to prevent damage from overheating. After waiting like 1 hour it probably comes back on. Make sure hose, filters, bag (if an ... Vacuums

Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn

... Vacuums

When I turn the vaccuum on the roller works for about 20 seconds, then I hear an awful, loud noise, and the roller does not work. Sounds like maybe some gears are being stripped? Please help

It sounds like you need to change the belts. You can get replacements and view the manual here:Dyson DC07 Belts and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!

Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Dyson DC07 animal ( purple). If you are standing behind the vacuum I am missing the lower righthand connection...therefore whatever is suctioned up comes out at that point just over the back wheel. I would like to purchase a replacement for this part. In the manual I believe this part is labeled as C. Can this part be purchased separately ?Please Help....

Hi there SmartAlec from NelsonVacuums.com.au i am not sure if you are based in australia but if you are you can ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!

Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????

Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.

Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

My Dyson DC31 runs for a few seconds then cuts out and won't work at all. It is fully charged. We bought it just over 2 years ago and it has worked perfectly until now. It is clean and has no apparent blockages. Please can you help?

Hi Jean, it's Jack at Dyson.I'm sorry to hear you're having difficulty with your DC31. If it cuts out in use when it's fully charged, we'd need to take you through some quick diagnostic checks when you have the machine at hand. This will help ... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a DC25 that I just bought in Dec 10. The last few times I vacuumed the carpet, the beater bar worked on and off. Now it does not move at all. I took off the beater bar to see if there were any obstructions, but there were none. Could you please help me with this. Right now my husband is saying that we should not have bought such an expensive vacuum (which he has said all along). I want to prove him wrong!! Up til a couple of weeks ago, it was working perfectly and I have loved it!

This is a good quality machine which I am sure wil last a long time in answer to your question make sure that the setting is set for carpet and not just flooring ..the head needs to be flat on the floor for the beater to work .I am assuming that thi ... Dyson DC25 All Floors Bagless Upright Vacuum

Vacuum works fine when using the attachments, but as soon as we try to use it in it's normal upright position it does not work. We have cleaned all filters and removed debris from roller, but nothing has helped.

Greetings,\015\012\015\012There could be a few things that would cause your Dyson to do this. I will give you detailed step by step instructions along with pictures on how you can diagnose this problem. \015\012\015\012Po ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi: We ahve a Tornado CV30 vacuum. The suction does not seems to be working properly. There is no suction at the tool hose and the bag does not seem to have air moving into it. Do you think there is a clog somewhere? The roller is moving. Thank you for youre help :) Kelly Branson, Mo.

To clear the clog, remove the hose and wand from the unit and separate them. The hose is\015\012released by pressing the white plastic ring in the housing. The two are\015\012separated by simply unscrewing them. Remember this threaded connection\015\ ... Tornado 93030 Wide Area Carpetkeeper Upright Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!

... Hoover Steamvac F5860-900 Vacuum

I have an eye vac professional that will not stay on to **** up the dirt. There is power to the outlet and the blue on/off light does stay on, but in Auto mode if I stick my hand near the dirt sensor it just pulses on and off. I can feel the suction, but it won't stay on. I've unplugged it, removed the dirt bin and filters and nothing works. Help!!!! This is brand new and I've only emptied the collection bin once and it hasn't worked since.

... Vacuums

I have a roomba 435. I've had it for about 3 months, it had been working great until it started to sound a little different (louder). Now I noticed that it doesn't pick things up, it just pushes them around, I then discovered that the brushes aren't turning. I cleaned them out, no parts are missing. Brushes still won't turn. Help please.

Hmmmm....I know exactly what this is... Think back...the last time it was used when it worked...did it pick up something like a sock or get stuck somwhere?????? If you look on Ebay, it is polluted with this model Roomba. There is a gear that strips. ... iRobot Roomba 410 Robotic Vacuum

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks

Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

I have an older Oreck XL that has worked great. The belt recently broke and I reinstalled a new one but now there's a rattling noise like something is loose and a burning smell. I've cleaned it as well as I could but still nothing. Help please!

When you turn it on, is the brush roll spinning? (Check carefully, as lifting the unit from the floor exposes a brushroll that should be spinning at a high RPM.)\015\012\015\012Did you get the brush roll properly seated in the slots? Does ... Oreck XL Ultra Bagged Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1328 seconds