Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

I asked about how to replace a belt on my sebo cleaner automatic X1 I have lost the answer can you tell me again please?


Answers :

This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years.
So, here's how to get at the belts and change them... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine.

STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!
STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS. All the surface-mounted screws are irrelevant to this job.
STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum tubes out of vertical. The top cover will then lift off. You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the right of that double pulley is the electronic circuit board - note that it has a sensor that locates within the pulley device, be careful not to damage it.
STEP 4. At the left end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back. Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.
STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). Then undo the four screws holding the double pulley. Once that's free, you'll be able to change the belts.
Re-assembly is simply the reverse of the above process.
If you need more help, just ask. Please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I asked about how to replace a belt on my sebo cleaner automatic X1 I have lost the answer can you tell me again please?


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get at the belts ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01


... Vacuums

Belt replacement can you tell me how i replace the belt on my electrolux velocity hoover please


Need to know if it is a Electrolux or a Hoover and the model number. ... Vacuums

Could you please tell me how to replace a belt on hoover please


Please identify the product model number.\015\012It will be on the data label, probably a UXXXX-XXX series. ... Vacuums

My hoover turbo cyclonic needs a new belt replacement I 'am not sure how to change it please tell me how to change the belt


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.


Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Hi, The belt of our Dirt devil bagless vaccum broke and we got new belt and replaced it. Even after replacing the belt, the brush is not rotating. Any suggestions please ?


Did you check to see that the beater brush, the brush that the belt drives, is free of debris and moves freely?\015\012When they bind up they can cause the belt to break.\015\012Remove the beater brush just as you do when changing the belt and clean ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My belt broke and I cannot find a replacement anywhere. Can you tell me where I can buy replacement Sweep n Groom belts for my central vacuum system.


You can get replacement Sweep n Groom belts here:\015\012\015\012Sweep n Groom Belts ... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Where does it go and how do I replace the belt on a Deluxe Hoover Mach 3.8 bagged windtunnel action vacuum? I kno it goes somewhere around the brush but it fell off when opened and I can't tell where it goes. I have a replacement belt


... Hoover Vacuums

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks


Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

How do I replace the belt on a Bissel Powerlifter rug shampooer? I have removed the door that is marked "access belts". The problem is that I don't see how to get the belt around the lower roller. There is no problem getting the belt around the upper prong. Please advise.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Dirt Devil Swivel Glide Vac with a broken belt. I have purchased the correct belt(#4).The bottom is off and I cannot tell where the belt connects to. Please help. Jann


It connects to the left side with the little metal rod sticking out.then connect to the wooden roller. in the space without the brush on it. roll the wooden piece to check if everything moves. then put back together. ... Dirt Devil Vacuums

Lost battery charger AD-1215-US. Need replacement. Pls advise. Please advise how I can order a replacement


You can call this number 1-800-798-7398 and order by phone...i got it from the shark euro pro website...all they need is your model number ... Euro-Pro S3325 Handheld Steam Vacuum

I have a dyson dc07 upright which no longer picks up lent and hair. The roller brush is not spinning when the vacuum is turned on. How can I tell if it is the belt that needs to be replaced or the clutch and belts?


Need replaced Clutch Assy and Brushbar \015\012\015\012Clutch Assy part no:900252-04\015\012\015\012Brushbar Assy part no:904174-01\015\012\015\012try cleaning all Hose\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Eureka The boss Smartvac Model #4870 roller brush won't turn even on the highest setting and the belt smells hot. we took the belt off. How can you tell if it needs replaced?


Just by what you explained I can tell that it needs to be replaced. The belt doesn't have to be broken to need replacing, if it is stretched and worn then it will slip on the motor shaft and not turn the brush roll and get hot. Here is a link to the ... Eureka Smartvac 4870 Bagged Upright Vacuum

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of


Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

Hoover 2000W dust manager cyclone- Have had this for about 2 months and the brushes stopped turning thinking that the belt had acme off turned it over to try to get in to look at belt now the bottom wheels have came off and will not go back on have not lost any bits literally just undid one screw! Please help!


... Hoover Vacuums

Belt broke I need to find out how to get in the vacuum to replace the belt but cannot figure it out. I do not have the owners manual for this Eurka The Boss Superlit bagless (402a) please e-mail me any directions if you know how to do it,thanks. [email protected]


How do i change the belt on my eureka the boss lite vacum ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough


The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum

The small belt that makes the beater bars spin broke. It is only two years old; repair shops tell me this involves replacing two belts because of some kind of clutch to the tune of $150! Is this possible to repair myself


A very easy replacement. The belts cost about £3 each. Yes, there are two belts and even if the clutch needed replacement, this is about £20 for clutch and both belts http://www.dysonpartsdirect.co.uk/dysonparts/dc07belts.shtml - this is ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a broken belt brush on the bissell pro heat and thought I had a replacement belt. can you tell by this number if it goes to that machine bando sts 60 s3m 267


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0956 seconds