Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

Roller not turning - Sebo Automatic X1 Bagged Upright Vacuum


Answers :

If the motor runs when you switch on, but the brush roll doesn't revolve, then there may be a broken belt. I wonder how old your vac is? Sebo belts are very high quality and they usually last 10 years at least.\015\012
\015\012Before you go to the trouble of checking the belts, check the brush roll and its drive shaft. Remove the brush roll and check for signs of damage at the end where it engages the drive shaft. Also see if you can easily rotate the drive shaft - if you can, there's a belt broken. To confirm, lie the machine down so you can see the drive shaft, then switch on (keep fingers clear!) and look to see if the shaft is rotating. If you can't turn the shaft by hand and it does rotate when you switch on, then the belts are OK but the brush roll may not be locating properly and you probably need a new one.
\015\012
\015\012To check the belts you need to get the cover off the base, as follows: separate the base from the bag compartment by pressing the button at front bottom of bag compartment then just pull the two apart (a gentle lever may help). Then turn the base over and undo ONLY the four deeply recessed screws (you will need a cross-head screwdriver). Turn the base right-way up again and lift off the cover. You will then see the belts.\015\012
\015\012If you find the belts are both good, or if you find one broken and need further help, post a reply here, tell me what you've found, and I'll guide you through the next steps.\015\012
\015\012Good luck!
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller not turning - Sebo Automatic X1 Bagged Upright Vacuum


If the motor runs when you switch on, but the brush roll doesn't revolve, then there may be a broken belt. I wonder how old your vac is? Sebo belts are very high quality and they usually last 10 years at least.\015\012\015\012Before you go to t ... Sebo Automatic X1 Bagged Upright Vacuum

Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

1.1 sebo hard to push - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

Sebo Automatic x4 re-attach Foot Pedal - Sebo X4 Bagged Upright Vacuum


... Sebo X4 Bagged Upright Vacuum

Rollers not turning - Dyson DC33 Bagged Upright Vacuum


Be sure to engage your clutch. If the clutch is engaged the either the clutch is bad or the belts are stretched.If you have any other questions feel free to contact me.Tim ... Dyson DC33 Bagged Upright Vacuum

Bissel roller not turning - Bissell 3522 PowerForce Bagged Upright Vacuum


Hey, brush not turning can be quite frustrating. Here's a quick link to troubleshooting steps to assist you.\012\012http://www.bissell.co ... Bissell 3522 PowerForce Bagged Upright Vacuum

How to replace a belt - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed ... Sebo Automatic X1 Bagged Upright Vacuum

Poor cable connection in handle - Sebo Automatic X1 Bagged Upright Vacuum


You will have to open handle where switch is . undo screws where power cable goes into switch. Cut +/- 100mm off exsisting cable & rewire . ... Sebo Automatic X1 Bagged Upright Vacuum

Will not turn on when plugged in - Sebo X4 Bagged Upright Vacuum


Hi There,So when this light is displaying, it's says "Bag Full or Clog" on the indicator. If you have changed the bag, and it's still showing this light, it means that you either have a clog in the vacuum, or your filters are dirty, which ... Sebo X4 Bagged Upright Vacuum

How do you cheng the filter - Sebo Automatic X1 Bagged Upright Vacuum


The Sebo X1 has 2 filters. Both should be changed once for every 20 bag changes. The long cylindrical filter in the bag compartment just slides out to the front - grab the little handle at the bottom and pull forwards - it can be a bit stuck, so you ... Sebo Automatic X1 Bagged Upright Vacuum

Vaccum blowing not sucking - Sebo Automatic X1 Bagged Upright Vacuum


Sounds like you've got a plug. Take the hose off, it should be plain to see if its in the wand or in the hose. Work your way from the bottom to where it goes into the bag but it's almost always in the base where the dirt turns to go up the hose. Ther ... Sebo Automatic X1 Bagged Upright Vacuum

Dyson dc33 bagless roller brush won't turn - Dyson DC33 Bagged Upright Vacuum


... Dyson DC33 Bagged Upright Vacuum

Roller won't turn - Kirby Ultimate G Bagged Upright Vacuum


This is most likely due to a broken belt. See following site for an instructional video for replacing the belt.\015\012\015\012http://www.kirby.com/Port ... Kirby Ultimate G Bagged Upright Vacuum

Replaced belt but isn't tight to turn roller - Eureka Smartvac 4870 Bagged Upright Vacuum


Are you sure that you have the right replacement belt? Here is a link to the belt you should have and the manual:Eureka 4870 Belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Eureka Smartvac 4870 Bagged Upright Vacuum Smokes when I turn it on


Check the air intake! Its probably clogged! ... Eureka Smartvac 4870 Bagged Upright Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Vacuum sebo not going up and down - Sebo X4 Bagged Upright Vacuum


... Sebo X4 Bagged Upright Vacuum

Sebo upright vacuum cleaner - Bag full or clog light on constantly when using as an upright but not when using detachment pipe. Bag changed and no sign of blockage. Is this a common fault or does it need to be taken apart by an authorised repairer?


Hello,\015\012\015\012I have actually written an in depth trouble shooting guide on how to find the clog in your Sebo. Since this light is coming on only when you have the wand inserted into the vacuum and are vacuuming the floor, this i ... Vacuums

Poor suction on Sebo x4 - new bag inserted - Sebo X4 Extra Bagged Upright Vacuum


... Sebo X4 Extra Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Vacuum is not turning on - Oreck XL Ultra Bagged Upright Vacuum


Try a ruling out a couple of things first before opening up the handle:\015\012\015\0121) First lets make sure your outlet has power\015\012 a) can you plug anything else in and have it work?\015\012 b) is the vacuum plugged ... Oreck XL Ultra Bagged Upright Vacuum

Vacuum is turning on and off intermittently - Hoover Breathe Easy U5250-930 Bagged Upright Vacuum


Turn the vacuum ON.\012Go to the plug while it is in the outlet, jiggle it and the wire going into it to see if there is a loose connection on that end. \012Then go to where the wire enters the vacuum.\012Jiggle that to see if that ... Hoover Breathe Easy U5250-930 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1177 seconds