Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

Changing the belt on a sebo upright vacuum cleaner


Answers :

This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years.
So, here's how to get at the belts and change them... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine.

STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!
STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS. All the surface-mounted screws are irrelevant to this job.
STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum tubes out of vertical. The top cover will then lift off. You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the right of that double pulley is the electronic circuit board - note that it has a sensor that locates within the pulley device, be careful not to damage it.
STEP 4. At the left end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back. Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.
STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). Then undo the four screws holding the double pulley. Once that's free, you'll be able to change the belts.
Re-assembly is simply the reverse of the above process.
If you need more help, just ask. Please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Changing the belt on a sebo upright vacuum cleaner


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get ... Sebo Automatic X1 Bagged Upright Vacuum

Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.


... Vacuums

Upright vacuum cleaner model dm4485 belt change assistance


... Hoover Vacuums

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

How do I change the belt on a vacuum cleaner - Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum


You don't. Call cust. service, they sound send a new head. ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Sebo upright vacuum cleaner - Bag full or clog light on constantly when using as an upright but not when using detachment pipe. Bag changed and no sign of blockage. Is this a common fault or does it need to be taken apart by an authorised repairer?


Hello,\015\012\015\012I have actually written an in depth trouble shooting guide on how to find the clog in your Sebo. Since this light is coming on only when you have the wand inserted into the vacuum and are vacuuming the floor, this i ... Vacuums

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have model a Riccar 8905 upright vacuum cleaner. When changing the belt a part fell out and I don't know where to put it or what it does.


... Riccar Vacuums

How do i change belt - Dyson DC14 All Floors Upright Vacuum Cleaner


Hi there,I am sorry to hear you are having difficulty with your DC14. If the belt has broken completely, the clutch assembly will also need to be replaced. We recommend the clutch be replaced by a Dyson authorized technician. However, if your ... Dyson DC14 All Floors Upright Vacuum Cleaner

Change the belt - Clarke CarpetMaster 215 Upright HEPA Vacuum Cleaner With Onboard Tool


... Clarke CarpetMaster 215 Upright HEPA Vacuum Cleaner With Onboard Tool

How do you change the belt? - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How to change belt in hoover core 3 upright bagless vacuum cleaner


... Vacuums

Need help need to change belt on a model #1489a upright vacuum cleaner.


... Eureka Vacuums

How do you change the belt for the brushes - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Turn the vacuum upside down, there should be two thumb release pivot screws. Remove bottom cover, now you have access to the belt. Remove belt that's in figure eight position, then reinstall same as above with figure eight position. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do you change the belt - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi there SmartAlec from NelsonVacuums.com.au here. Bissell have a very good guide on their website bissell.com.au here is a link to the product i think you have ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How do I change the Brush Belt? - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


It depends on the type of ProHeat cleaner you have. But you can go to www.bissell.com and download the manual for your model and you can get the belt you need at ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How to change a belt on a hoovr upright purepower vacuum cleaner


A very easy procedure!\015\012\015\012Look at the front hood of the Purepower (where all the lettering is including the 1600 or whatever the model number and name is located at) and you'll see at the back two screws either side where the back w ... Hoover Vacuums

How do u change the brush belt - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Here is a link to the belts you need and a manual you can\015\012view which has instructions:Bissell Carpet Cleaner Belt and Manual ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How to change the belt on a Hoover High Performance upright vacuum cleaner


Chang the belt ... Vacuums

Trying to change belt in kenmore 3116890 upright vacuum cleaner model116. Can't open vac


... Kenmore Vacuums

Dyson14 all floors i need to change belt - Dyson DC14 All Floors Upright Vacuum Cleaner


This video will show you ... Dyson DC14 All Floors Upright Vacuum Cleaner

How do you change a belt on an upright bissel vacuum cleaner


Just a couple screws on the left side of machine. easy fix. ... Bissell 9200 Upright Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

I have the Bissell upright cleanview bagless vacuum cleaner. My belt broke and someone else took it off. I bought a new belt but do not know where it goes on the cleaner. Please help


Easy to do. Unplug the vac. Turn the vacuum over and look for three finger latches on the bottom behind the brushes. Unlatch these and pull the faceplate off. Then, grab one side of the brush and pull straight up (they just sit in grooves on the ... Bissell CleanView 3596 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4469 seconds