Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

X1.1 model has plenty of suction through the nozzle, but doesn't 'pull' across the floor anymore or pickup dirt when using upright

Answers :

Assuming that the automatic height adjuster is working properly, most likely your Sebo needs a new brush roll because the bristles on the old one are worn to the limit. To test the height adjuster, put the machine in the normal operating position (with the handle not upright) then switch on - the green "down" light may come on briefly (or may stay on if the brush is worn). Then, leaving the machine switched on, move the handle to the locked upright position - the green "up" light should come on, and you may be able to see the whole machine tilt backwards slightly as it lifts the brush off the floor. If that happens, the adjuster is working properly and you definitely need a new brush roll.\012
\012I hope this helps. If you need more guidance, just post a reply here and I'll get back to you soon. Please remember to rate this answer as I do value feedback. Good luck!
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

X1.1 model has plenty of suction through the nozzle, but doesn't 'pull' across the floor anymore or pickup dirt when using upright

Assuming that the automatic height adjuster is working properly, most likely your Sebo needs a new brush roll because the bristles on the old one are worn to the limit. To test the height adjuster, put the machine in the normal operating position (wi ... Sebo Automatic X1 Bagged Upright Vacuum

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?

... Bissell Vacuums

I am using a Dirt Devel upright vacuum. How do you start the suction of the hose for upholstery etc. as opposed to floors.

There maybe a dial to turn the floor suction to the hose/wand. normally these are located at th base of the machine. ... Vacuums

When using dyson in upright possition does not pick up very well. roller is going round. when you press front to begin hoovering carpets the front doesnt seem to drop onto floor low enough. dont think suction pipe is engaging properly !!!!!!.

Hi Peter, I'm sorry to hear you're having difficulties with your DC07. It sounds as if the internal hose may have become twisted - you should be able to resolve this by removing and replacing it as shown in the video below. Please make sure t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc17 turns off when its upright, so when I go to use the attachments it doesnt turn on unless I go to vaccume the floor. whats going on?

Hi there,I'm sorry to hear you're having difficulties with your DC17. Your issue sounds unusual, and we'd appreciate the opportunity to help resolve it. Please call our Helpline free on 1-866-693-9766 - or if you'd prefer, you can email your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Our Riccar SupraLite Upright Vac used to glide across the floor so easily, but now we have to push it pretty hard. This just recently started. What can be wrong?

Suggest you check the wheels to see if they are moving freely.\015\012Also check the beater brush to see that it is moving freely.\015\012Be sure the belt has not broken. If it has, replace with a new one.\015\012Also take the time to clean the beat ... Riccar 8955 Upright Vacuum

My dirt devil easy lite cyclonic does not suck up the dirt or anything on the floor anymore the rollers still roll. It stop sucking.

Check and make sure that the pickup tube from the bottom of the sweeper to the waste cup does not have a clog anywhere you can use a metal coat hanger and straighten it out and carefully run that thru. ... Vacuums

There is a rubber valve on the top of Dyson DC14 all floors. When the vacum is locked in its upright position or the hand wand is used there is a whistling sound coming out of the valve. When the vac is used as a floor vac, it does not make the sound. Is this something that I can fix? Is there an obstruction somewhere that would be causing this sound? thank you.

The Fixya user in this repair is giving out personal contact information rather then helping the customer out on the Fixya board. This defeats the whole purpose of Fixya if the "TheDysonTeam" just gives out his phone number and helps the customer o ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?

Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected in ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Kirby runs across floor on own and is hard to pull back

... Kirby Ultimate G Bagged Upright Vacuum

DC17 doesnt move on floor good

Also be sure the 2 springs are still underneath. I think those help level out the vacuum on various surfaces. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?

Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums

I need the dirt devil floorkeeper manual. - Dirt Devil CE5500 Floor Keeper Upright Wet/Dry Vacuum

... Dirt Devil CE5500 Floor Keeper Upright Wet/Dry Vacuum

My vacuum doesnt **** dirt from the floor but sucks dirt with the nozzle.

Probably have a clogged intake from the beater bar thru to the vac system.. Try this.. with the vac unplugged, flip the vac over so you can get to the bottom of the vac head near where the brush rotates.. then depending on the model.. remove the cove ... Eureka Vacuums

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.

I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hello- my motor filter is becoming clogged every time i use it. i have removed and washed it--I thought maybe i didn't have the lid closed tight enough but for some reason dirt is pouring into the filter, it seems that some of the dirt suctioned is actually being pulled into the filter intead of the canister

One way or another, dirty air is by-passing the cyclone. My best guess is that when you emptied the clear bin, a seal has dropped out (or become displaced) and the base of the clear bin is no longer sealing properly against the bottom of the cy ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil

Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

Vaccuum issue I just bought a Eureka upright model 5892 BVZ, my concern is, I bought it on sale (floor model) and it didn't have a manual with it. I took it home and tried it, and although it appears to be working very well there is not dirt in the catch bin on the front of the unit. I tried the hose w/attachment and again it worked very well in picking up the cat hair, but where does the hair and the dirt go, I am afraid it is spitting it back out somewhere since I can not see anything in the c

If the dirt being vacuumed is not going into the dirt cup, then it must be just stuck in the hose and evenually will clog up. Check the hose and see it there is a clog in it, otherwise you have a years warranty on a new vacuum, take it into a warran ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

When I use my Dyson in the upright position it does not **** up the dirt on the carpet. But if I attach a tool and use the hose it does. I have checked to see if there is a blockage any where and there does not seem to be

Hi its Darran at Dyson.I would recommend checking the brush bar to see if its spinning when you switch the machine on and release the head into the vacuuming position. If its not, check the brush control dial on the head of the cleaner to ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Kirby Ultimate Diamond Edition G Series, upright. Problem: I lost my manual. How do I use my vacuum on hard wood floors? How do I use attachments, where do they attach?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=576029\015\012Generic problem for all Vacuums\015\012Kirby Ultimate Diamond Edition G\015\012Posted by jlutsi on ... Vacuums

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria

It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

Dirt doesn't make it to cannister ...it used to have the spin around affect now it just sits there but some dirt is leaving floor....it is in the hose..I have cleaned ALL filters ...YUCK......help

You have a broken belt. Turn the vacuum over and remove cover plate. You will probably find a broken rubber belt. Buy a new belt for your vacuum. Remove the brush , install the new belt with the brush. Put cover plate back on. You are ready to go! ... Bissell 6594 PowerForce Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0996 seconds