Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


Answers :

OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at it.
STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!
STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS. All the surface-mounted screws are irrelevant to this job.
STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum tubes out of vertical. The top cover will then lift off. You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pulley is the electronic circuit board - note that it has a sensor that locates within the pulley device, be careful not to damage it.
STEP 4. At the right end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back. Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.
STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). Then undo the four screws holding the double pulley. Once that's free, you'll be able to change the belts.
Re-assembly is simply the reverse of the above process.
If you need more help, just ask. I value your feedback, so please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

How to replace a belt - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed ... Sebo Automatic X1 Bagged Upright Vacuum

Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

Sebo upright vacuum cleaner - Bag full or clog light on constantly when using as an upright but not when using detachment pipe. Bag changed and no sign of blockage. Is this a common fault or does it need to be taken apart by an authorised repairer?


Hello,\015\012\015\012I have actually written an in depth trouble shooting guide on how to find the clog in your Sebo. Since this light is coming on only when you have the wand inserted into the vacuum and are vacuuming the floor, this i ... Vacuums

Changed bag & will not come on now - Sebo X4 Bagged Upright Vacuum


Go please to www.sebo.co.uk go to section support and select your model for troubleshooting.and fix it God bless you ... Sebo X4 Bagged Upright Vacuum

Sebo Automatic x4 re-attach Foot Pedal - Sebo X4 Bagged Upright Vacuum


... Sebo X4 Bagged Upright Vacuum

1.1 sebo hard to push - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

Change belt on hoover savvy bag and bagless upright vacuum


... Hoover U8155-900 Savvy Bagged Upright Vacuum

HOW TO CHANGE A BELT - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum


Hi there...You will need a Phillips screwdriver to get the bottom cover off.Remove the screws and then remove the bottom cover.Clean out any excess dirt in the general area of the roller bar and motor assembly area.Place one end of the belt over the ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How do I change the belt? - Eureka Smartvac 4870 Bagged Upright Vacuum


Turn the vacuum over so the bottom is up.. Remove scews from plate surrounding the brush area..\015\012Pop of the cover plate..\015\012Lift out the side of the brush that the belt connects to..\015\012Put new belt on..\015\012 ... Eureka Smartvac 4870 Bagged Upright Vacuum

Changed belt. have burning smell - Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum


Take it back apart, check it again. Check the plastic where the belt is running for burnt spots. Also check the brush roller sometimes the tension from a new belt can finish off what was left of the bearings and cause the plastic end caps and roller ... Hoover U5434-900 WindTunnel Plus Bagged Upright Vacuum

Change the belt - Eureka Smartvac 4870 Bagged Upright Vacuum


Hi There,Here's how you can replace the belt on your Eureka SmartVac 4870. I have taken pictures of the repair to help you better with this.Here's what you'll need in order to complete this repair:- ... Eureka Smartvac 4870 Bagged Upright Vacuum

Change belt in hoover turbopower 1500 vaccum - Hoover U5046-930 Turbopower Bagged Upright Vacuum


... Hoover U5046-930 Turbopower Bagged Upright Vacuum

No manual, how do you change the belt? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

Belt change for model #u4258-930 - Hoover Runabout U50-940 Bagged Upright Vacuum


Hi,This link will take you to a site with instructionsand illustrations to help you change your belt.http://www.info-vacuum-cleaner.com/hoover-va ... Hoover Runabout U50-940 Bagged Upright Vacuum

How do you cheng the filter - Sebo Automatic X1 Bagged Upright Vacuum


The Sebo X1 has 2 filters. Both should be changed once for every 20 bag changes. The long cylindrical filter in the bag compartment just slides out to the front - grab the little handle at the bottom and pull forwards - it can be a bit stuck, so you ... Sebo Automatic X1 Bagged Upright Vacuum

Vaccum blowing not sucking - Sebo Automatic X1 Bagged Upright Vacuum


Sounds like you've got a plug. Take the hose off, it should be plain to see if its in the wand or in the hose. Work your way from the bottom to where it goes into the bag but it's almost always in the base where the dirt turns to go up the hose. Ther ... Sebo Automatic X1 Bagged Upright Vacuum

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.


Its still clogged, you gotta dig deeper ... Vacuums

Roller not turning - Sebo Automatic X1 Bagged Upright Vacuum


If the motor runs when you switch on, but the brush roll doesn't revolve, then there may be a broken belt. I wonder how old your vac is? Sebo belts are very high quality and they usually last 10 years at least.\015\012\015\012Before you go to t ... Sebo Automatic X1 Bagged Upright Vacuum

Have eureka victory upright bag vacuum model 4325 how to get into machine to change out the belt


There are four holes on each side of the top of the hood. There is a screw on each side, inside one of those holes. You have to take those two screws out to remove the hood. ... Eureka Vacuums

Change belt on oreck xl intellashield - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Changing the belt on a sebo upright vacuum cleaner


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get ... Sebo Automatic X1 Bagged Upright Vacuum

How to change g5 belt - Kirby G5 Bagged Upright Vacuum


1)First, you turn the square belt lifter on the front of the power nozzle until the red arrows line up (belt off) \015\0122)Remove the power head from the front of the machine. Now turn\015\012the belt lifter the other way and line the green ar ... Kirby G5 Bagged Upright Vacuum

How do you change the belt? - Oreck XL Ultra Bagged Upright Vacuum


Two methods:\015\012\015\0121) If your vacuum has the small side door on the cover of the lower unit, can remove the screw, it will allow you to access the belt. I assume old belt is broken, so what you see will be the end of the motor sh ... Oreck XL Ultra Bagged Upright Vacuum

How do i change my belt on the kirby g6 - Kirby G6 Bagged Upright Vacuum


Hello,For detailed, step by step instructions (with pictures):http://www.goodvac.com/articles.asp?id=143Hope this helps! Ple ... Kirby G6 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0933 seconds