Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

How do you change the belts on the sebo automatic x1


Answers :

OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at it.
STEP 1. Separate the base from the bag compartment: press the button at bottom front centre of bag compartment and lift bag compartment upwards away from base. Sometimes this is quite stiff and four hands would be useful, you can lever it from behind with something relatively soft (the plastic handle of a dishwash brush works well) but take care to lift vertically upwards, not sideways or you risk bending a metal lever that's hard to get back into shape again. Rest assured that once you've pressed that button there is nothing holding the two parts together other than friction!
STEP 2. Turn the base upside-down and undo the FOUR DEEPLY-RECESSED SCREWS. All the surface-mounted screws are irrelevant to this job.
STEP 3. Turn the complete base right-way up, release the foot pedal and move the vacuum tubes out of vertical. The top cover will then lift off. You will see there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pulley is the electronic circuit board - note that it has a sensor that locates within the pulley device, be careful not to damage it.
STEP 4. At the right end of the motor cover, the drive cog is concealed by a small cover. Lift this cover out vertically, noting how it locates in the frame for when you come to put it back. Next, although not essential, it helps to remove the metal lever because if it falls out when you're not looking you may later be uncertain about how to locate the small coil spring. So slide that lever out towards the motor, noting how the spring locates.
STEP 5. Undo the two screws holding the circuit board (take care the washers don't slip away). Then undo the four screws holding the double pulley. Once that's free, you'll be able to change the belts.
Re-assembly is simply the reverse of the above process.
If you need more help, just ask. I value your feedback, so please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

How do you change the belts on the sebo automatic x1


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're a ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo Automatic X1 cleaner, toothed belt replacement


OK, here goes... (there may be more detail here than you need, but it's a copy of a solution I wrote for someone else)  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. \015\0 ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo Automatic X1 Stopped. Yesterday my Sebo stopped working. I know this can happen if it gets blocked and overheated so I checked for blockages, none. And left it too cool down. Tried it again but it was completely dead, Changed the fuse and it ran for 1 second and stopped again. Any ideas?


Hello,\015\012\015\012Ok, thanks for the clarification. Even though the cord doesn't have any external damage, it's still very possible that it has gone bad. When a Sebo upright doesn ... Sebo Automatic X1 Bagged Upright Vacuum

Replacing a belt on a Sebo Automatic X1 vacuum cleaner


The roller brush has stopped turning, I think it could be the belt, how do I seperate the top from the bottom?\015\012\015\012I will await your reply.\015\012\015\012Thankyou Val\015\012 ... Sebo Automatic X1 Bagged Upright Vacuum

How to change a belt on a sebo bs36 - Vacuums


... Vacuums

How to replace a belt - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed ... Sebo Automatic X1 Bagged Upright Vacuum

Changing the belt on a sebo upright vacuum cleaner


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get ... Sebo Automatic X1 Bagged Upright Vacuum

I asked about how to replace a belt on my sebo cleaner automatic X1 I have lost the answer can you tell me again please?


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get at the belts ... Sebo Automatic X1 Bagged Upright Vacuum

Belts on Sebo Automatic XP1 - Vacuums


I am not sure of the question about the belts. This is information I have found and maybe I will answer your question.\015\012\015\012This link is a parts breakdown of your machine.\015\012 ... Vacuums

Brush spindle on Sebo automatic x1 is not rotating but suction power is OK the belt is OK


... Sebo Vacuums

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Changing belt Please advise how to change the belt. I wasn't the person who took the belt off, didn't watch. Now it's just me and the belt. I had 2, but 1st one burnt right off. Apparently I didn't have in the right spot! don't want to waste the only other new belt I have. Pictures would be greatly appreciated!!!!!!! Thanks Tammy Can call 920-660-0680


Step 1: Lower handle to floor to change belt Step 2: Remove the two screws from the top hood on the footStep 3: Lift hood to remove Step 4: Lift right end of brushroll (the belt end) Step 5: Remove and discard belt.Step ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.


... Hoover U4270-930 Vacuum

Changing belt how do you change the belt on the power steamer there is nothing on bissells webiste i need to change the one on the sie not the rollers


Take the water and solution tank out of the machine. turn it over an on the left hand side you will see a red clip with a screw in it. take out that screw. flip the unit back over and take off the belt access cover by sticking a straight screw dri ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How do I change the belt on the side. Have a Bissell Power Lifter. The belt broke and i cannot get it changed. HOW do I change it?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Sebo Automatic X1 vacuum cleaner doesn't produce much suction.


If the motor really is working, the problem is most likely to be that there's a blockage somewhere, and on this excellent vacuum cleaner there aren't too many places to look. You've probably already looked in the inspection flap on the underside. If ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo automatic X1. After switching on the motor


As sure as possible without actually seeing your machine, the carbon brushes on the motor are worn out. They are quite easy to replace (and not expensive). If you need help with doing the job, just post a reply here and I'll guide you as best I can. ... Sebo Automatic X1 Bagged Upright Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym


Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Belt changing dco4 how to change drive belt


Which belt clutch or brush ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Change belt how do I change che belt??


Remove the bottom plate, the V belt goes around the inner pulley and then the brush roll. The flat belt goes around the motor shaft and will stretch to around the bigger pulley by the V belt. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I changed the belt on my vacuum,and the belt burned up,and snapped.Right after I changed it.Am I missing a piece??


Sometimes it can depend on the quality of the belt - if its brand new then it shouldn't snap the moment it is changed; if its an older belt sometimes they can break up the moment they're changed. Ensure that the model you have is correct with the cor ... Bissell Vacuums

Its the widepath bagged tempo, i need to change the belt but do not know how. How do i change the belt


If I recall correctly - there are screws in the bottom of the front piece that holds the roller, remove them and a plate will come off. Under the plate you will see the rollerbrush - it should pull out and has plastic tabs with bushings on the ends - ... Hoover Tempo Widepath Upright Vacuum - Blue

Sebo automatic x1 -


Check the hose for a clog, also check the dirt inlet by the brush roll, it may have a clog also. ... Sebo Automatic X1 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0456 seconds