Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

The lead on our machine is becoming frayed - is it possible to replace the lead and if so, how is it achieved? John Tuffley

Answers :

If you are refering to the Electrical Power Cord? Yes, this can be easily replaced or repaired.
\015\012Depending upon where the cord is damaged, you can either cut it a little shorter and install a replacement electrical plug end (available at any electrical parts store (Lowes, Home Depot, Radio Shack, etc) for about $2.50.
\015\012Or if the cord is damaged near the vacuum, you can purchase another cord or even make up one yourself how ever long you want it within reason.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The lead on our machine is becoming frayed - is it possible to replace the lead and if so, how is it achieved? John Tuffley

If you are refering to the Electrical Power Cord? Yes, this can be easily replaced or repaired. \015\012Depending upon where the cord is damaged, you can either cut it a little shorter and install a replacement electrical plug end (available ... Sebo Automatic X1 Bagged Upright Vacuum

Hi! I'm interested in purchasing a G3 model ; however , the seller says that the machine was working perfectly and then when switching power on a while later , the machine was " dead " . Other than the brushes , power switch or lead , is there perhaps a fuse at all which could possibly have burned out ? Thanks .

Greetings from GoVacuum.com,Unfortunately there is no fuse on a Kirby Generation model. In my 10 years of repairing Kirby's as well as other vacuums, I will tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's t ... Kirby Vacuums

I have a new Toyota RS2000 that I was bought as a gift. I received it without a manual which I have now obtained, but now I have gone to use it the power lead does not seem to fit into the machine. Is it possible I was supplied the wrong lead or am I doing something wrong?

It is quite possible that you were supplied the wrong lead, seeing that the manual was missing, the contents of the package might well have been tampered with. Contact the person who gave you the machine and ask them to either check wit ... Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

I think the pump needs to be replaced in my Bissell little green machine. Some water/solution is being pushed through but not enough to spray only drip, if I hold the machine up high while using it (ie on a table) it will spray a little. Is the pump easy to replace? is there anywhere to get a parts diagram?

I got my Little Green ProHeat when the product was first unveiled\015\012several years ago. Shortly thereafter, the nozzle itself developed a\015\012clog in the spray jet. Remove the nozzle from the end of the hose, and\015\012with the machine runn ... Bissell 1400 Little Green Pro Canister Steam Vacuum

I need to replace the switch and leads to my Riccar 1500p vacuum. I've already replaced the entire electric hose which is over $100. Where can I get the switch and leads?

... Riccar Vacuums

Please give directions to replace the lower shaft gear on my Pfaff 1222 sewing machine. How do I time the machine after replacing the gear?

... Vacuums

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?

The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have an old Rex 26-188 leather sewing machine, is it possible to find a manual for this machine. The serial number is T 704937. This is a functioning machine but I need to know how to thread it. Thank you. Lois White

... Vacuums

I own a old Bissell Big Green Cleaning Machine and am looking to replace the inline fluid/vaccum pump. The pump has an Eaton logo and is model CP7. I have not been able to find a replacement at your site. Could you tell me if one is still available or where I might find a replacement?

I just saw one on USAVacuum.com It's about $29 ... Vacuums

I have a Husqvarna Viking Designer sewing machine. The fuse blew in the machine and I am having trouble finding a replacement fuse. It is a T3.5/250v glass fuse. Please let me know where to find one. I have searched the internet high and low and can't find one. Radio Shack has a 3.0amp 250v slow blow fuse whick seems to be the right dimensions. Willl that work. Otherwise, I am not sure what to do and can't afford to take the machine to a repair show. Thank you.

That fuse will work no problem. There is no harm in trying it.The machine probably requires about 2 amps or less under normal operation. Being a 3.0 amp slow blow fuse, it will withstand short bursts of extra current when your machine get ... Vacuums

My Ultralux 2000 vacuum power head does not work on my machine but does work on a different machine. What are the possilbe problems? I tried replacing the hose with a new one and that didn't help.

It's probably due to bad wiring connections between the wands, hose and wand, or power nozzle and wand. If it came with the Sidekick, try using it on the end of the hose. If not, simply try using the power nozzle on the end of the hose (no wands). ... Electrolux Eureka Easy Clean 2 in 1 Stick and Handheld Vacuum Model 108A 1 ea

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?

Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!

... Hoover Steamvac F5860-900 Vacuum

My New Home DX2030 (older than dirt) balls up thread when I try to reverse. I cleaned bobbin holder, hook race and replaced needle, twice. I removed and replaced bobbin and rethreaded machine but no improvement

... Vacuums

How do i replace the handle hose for the bissel little green machine 1400-5? I did order the part but unsure how to connect it to machine? [email protected]

Take the flex hose clip and slide the back plate into the opening on the front of the unit. You will\015\012hear a "snap" when it is locked in place.\015\0122. Take the vacuum flex hose storage brac ... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

My handheld vaccum bag got full and the machine shut off. i cleaned the clog, replaced the bag, and the machine won't turn on.

Depending on the make and model you can sometimes find a reset button on it somewhere.. If I knew the make and model I could be more helpful with your issue. Thanks for choosing Fixya. ... Oreck Vacuums

Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I purchased a brand new Techno 1000 Fog Machine last Halloween. It worked fine, but once I ran the cleaning fluid through the fog machine only heated up and produced no fog. A year later and now won't even heat up at all, even after replacing the fuse!

... Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?

Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

CEL lit up on dash. Codes point to possible loose vacuum line or faulty gas cap. Replaced cap with no change. Looking for vacuum line diagram if possible. Thanks, Brian

\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

I have a Bissel steam cleaner and I had to replace the brush belt and I don't have a manual to replace it back on the machine.

Here is the manual for your model:User Guide (PDF) ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0792 seconds