Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds


Answers :

I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor at the worst.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No motor when switched on two red lights flash,cleaned hoover, put back together motor started,then cut out after a few seconds


I would double check your wiring, Make sure all wiring is tight. No cracks, no pinched wires. If needed, bypass the switch and see if it will stay running. If so, switch would be bad. If it's the same, then you have a wiring problem or a worn motor a ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

At first when I tried starting my B & S I primed the motor and it ran for a few seconds and died. This happened twice. I drained the tank and took apart the cvarb and blew out the entire carb. Put it back together changed the plug and now nothing. Could it be that the priming diaphriam (#694395) has a hole and thus preventing gas to come up from the carb bowl?


Hi tifix1...\012Yes, that could cause your problem.\012I will offer a few more things to check and repair/replace, maybe there is a few things that you missed.\012Please take time to rate me\012\012Sounds like you have d ... Vacuums

Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve


Yes, you can. ... Miele S318 Bagged Canister Vacuum

Hoover Upright U8185-900 agitator brush stopped working...took hood off...PCB display bridge fried...ordered new one & installed...that burned up in 15 seconds...ordered another PCB and new agitator motor...and since I was in there every **** thing else replaced also...took whole thing apart and cleanded even tho agitator brush was not jammed...put all back together...**** thing just sits there with red led lights displayed...this is ridiculous


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Bought a shop vac about 3-4 mos ago and while i was using it, it cut off and wont cut back on. This is the second shop vac that done this and I took the first one back and got this one and it did the same thing. It is a 12 gal. 4.5 peak hp.


... Shop Vac 401-12-00 Wet/Dry Vacuum

Where do you hook the clear hose that is in the compartment with the motor ? Second where the vacuum hose connects to the bag it keeps cutting in and out of power. I replaced the female cord to motor and still cuts out."no suction "


Would you care to tell us the make and model of the vacuum you're asking about? ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Motor My vacuum cut out as I was using it. After some experimenting I found that the circuit reset had gone off. When I tried a second time while near the motor , there was a flash and again the motor shut off. At this time I am guessing that the motor is faulty. The central vacuuming is approximately 12 years old.


If it tripped the reset again, I would probably agree with you. Check out centralvacuum.com for another motor. They aren't the cheapest, but they have excellent support. Good Luck!! ... Easy Flo EF1400 Central System Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Electrolux 2 in 1 Ergorapido stick Vacuum. Motor runs then cuts out after 3 - 4 seconds. Sometimes it will run properly for 10 minutes so batteries are good. Why does it cut our usually?


If the hand held is working correctly (By itself) try pulling up a little bit on the 4 metal connection tabs on the wand. The connection tabs were not making a proper connection on my unit. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

My Hoover Windtunnel cuts off after using it for a few minutes. After an hour or so, I can turn it back on again. This keeps happening every time I use it. This is my third one. I have taken the other two back to Target for the same problem and they have exchanged them.


Yes this machine has a thermal protector in it to shut off the machine if it gets to hot, this is normal. if there is no clogs in the hoses or in the machine then you will need to wash the filter at the top of the machine. you will have to remove the ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Dyson My Dyson DC04 runs for a second or two then stops. I have checked the motor. The brushes are good but the commutator is a slightly pitted.Do I need a new motor?


Hi.\015\012\015\012Check mains lead where it enters machine very common for internal fracture.\015\012\015\012To prove this try waggling lead with machine switched on if it starts & stops this is the fault.\015\012 ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.


It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor


On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I removed the filter from the motor in the ball. After I cleaned it and let it dry, I put it back in. From then on, it makes a moaning noise when I turn it off after I vacuum. I followed directions to clean it and put it back (it's pretty straight forward and fool proof). I've since cleaned the filter a second time, doing the same steps and it seems to have made it worse.


... Dyson DC25 All Floors Bagless Upright Vacuum

I have a vx550cc that keeps kicking in and out quickly, then shuts down for a few seconds and starts up kicking in and out again. There is lots of suction at all the outlets and sweeps. The dirt bucket has been emptied and the filter cleaned. Al the LED lights light up when the motor kicks out, then back to one green when it starts back up. This unit has worked great for four years with no problems.


... Broan-NuTone VX475 Bagged Central System Vacuum

Hi., If anyone could help it would be greatly appreciated, I have a Flair 3055 ventalation system in my house and over the last five years two fan motors have gone bad. it has been mickey moused together by a local repair man, and as of last week, it has died again. At 4-5 hundred a pop I would like to fix it myself, can anyone suggest a good replacement motor that will fit and work. My honey has breading problems and at this time of year, every penny is allocated, so time is of the essence. t


Hello George, Sorry about your predicament. Various fans are available for your unit but since you say the unit has been mickey moused together adjustments must have been made to the fan seating and system therefore if you order any particular fan th ... Vacuums

Kirby G4A I have just had the motor rewound it has taken 4 weeks to get it back .What I need is a work shop manual so I can put it back together. Help


YOU'RE WELCOME!! :0) ... Kirby G4 Bagged Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0714 seconds