Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?

Replacing a belt on a Sebo Automatic X1 vacuum cleaner

\015 The roller brush has stopped turning : someone suggested a broken belt may need replacement. How do I take off the top housing? Is it the 4 deep-set screws which allow the top to come off?\015

Answers :

The roller brush has stopped turning, I think it could be the belt, how do I seperate the top from the bottom?
\015\012
\015\012I will await your reply.
\015\012
\015\012Thankyou Val
\015\012
On the front near the bottom is a big push type button, push it in and pull the handle and bag asm. up to remove it from the power head. Then remove those 4 or 5 screws to release the top cover.
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing a belt on a Sebo Automatic X1 vacuum cleaner


The roller brush has stopped turning, I think it could be the belt, how do I seperate the top from the bottom?\015\012\015\012I will await your reply.\015\012\015\012Thankyou Val\015\012 ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo Automatic X1 cleaner, toothed belt replacement


OK, here goes... (there may be more detail here than you need, but it's a copy of a solution I wrote for someone else)  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. \015\0 ... Sebo Automatic X1 Bagged Upright Vacuum

I asked about how to replace a belt on my sebo cleaner automatic X1 I have lost the answer can you tell me again please?


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get at the belts ... Sebo Automatic X1 Bagged Upright Vacuum

How to replace a belt - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed ... Sebo Automatic X1 Bagged Upright Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.


Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

I need a replacement belt for a V1315 Shark Roadster Vacuum cleaner. Looks like there's no way to get one. Is there a compatible belt that will fit this vacuum?


... Euro-Pro Roadster V1315 Upright Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01


... Vacuums

Sebo Automatic X1 vacuum cleaner doesn't produce much suction.


If the motor really is working, the problem is most likely to be that there's a blockage somewhere, and on this excellent vacuum cleaner there aren't too many places to look. You've probably already looked in the inspection flap on the underside. If ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

I replaced the belts on my windtunnel vacuum u6439-900 cleaner..it works fine for a minute or so then it smells like burnt rubber and does not self propel. Does the v belt need to be taut or loose?


... Hoover Vacuums

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?


... Electrolux EUK71B Bagless Handheld Vacuum

I need to replace the agitator belt on a Hoover Elite U4465-9 upright vacuum cleaner. I have removed the bottom cover, but there is no access to the motor spindle to loop the belt around. How do I do this?


... Vacuums

Replacing belt on vacuum cleaner - Sharp Twin Energy EC-T2840 Bagged Upright Vacuum


... Sharp Twin Energy EC-T2840 Bagged Upright Vacuum

Replace belts on sharp vacuum cleaner - Sharp Twin Energy EC-TU2608 Vacuum


... Sharp Twin Energy EC-TU2608 Vacuum

Belt installation How do you install a #5 replacement belt on the Dirt Devil upright vacuum cleaner?


One end of the belt will go over the motor drive shaft and the other end will slip over the roller brush. Also, you can find this belt at www.vacbelts.com. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Hey i have a eureka 2971 BVZ upright vacuum cleaner and after removing the old belt to replace it. I accidently removed the Guard Belt and i can't remember how to put it back on.


... Eureka 2961AVZ Bagless Upright Vacuum

Vacuume cleaner not sucking up properly. Have replaced belt but belt keeps snapping?


Check to see taht with no belt in place the brush roll turns freely.There should be no resistance. If not remove hair and thread from ends of brush Then check the leveling screws on the end of the brush to be sure they are adjusted evenly. ... Kirby Ultimate G Bagged Upright Vacuum

How to replace the belt on model 8806-3 - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

It is not clear how to access the front spool on a Eureka 'Boss - smartvac' 4870K vacuum cleaner, when replacing the belt. Trying to force the flimsy black plastic lever attached to the shiny silver spool where the front end of the belt appears as if it should go, would cause breakage.


The shiny spool is the mechanism that stops the brushroll (brushroll control). The belt only slips around the brushroll, and the motor spindle. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

I have a Hoover Preferred vacuum cleaner and the belt is broke. i need instructions on how to replace the belt.


... Hoover Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1327 seconds