Having problems with your Sebo Automatic X1 Bagged Upright Vacuum ?
Height adjustment not working.
\015 'Up' and 'Down' lights do not light and vacuum body does not raise or lower. Brush still rotates and belts are fine. Any suggestions, or is it a service centre job?\015
It's likely the circuit board that controls the height adjustment motor, or the motor itself. Your local sebo service center will be better able to test to see just what is wrong. Though it wouldn't hurt to take a look at the boards sometimes they're visibly burnt, or connections can be loose. Good Luck!
Repair Help & Product Troubleshooting for Sebo Automatic X1 Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
We have the 3910T model. I am trying to get the height adjustment to work. I had taken apart the portion to change the belt and for some reason the height adjustment is not working. Is there a diagram on how to have the knob engage the other part?
... Bissell 3910 Bagless Upright Cyclonic Vacuum
I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?
The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums
Sebo auto X4 height adjustment not working
Worst case scenario is that there's a fault on the circuit board, but another possibility is that the brush roll is not rotating freely. The automatic height adjustment works by sensing the drag on the brush roll, and altering the height to maintain ... Vacuums
Height adjustment on Hoover Windtunnel u5755-900 no longer works
On this model it is only a single slide adjustment lever. have you trie to tilt the vac backwards (lifting the wieght off the front wheels) and then slide the adjustment lever?\015\012\015\012If there is a mechanical issue with it. take t ... Hoover Vacuums
Height adjustment not working
Manual says to tilt the vacuum back so the front wheels are off the ground (unit turned off of course) and make the adjustment. May take some back-and-forth force, but should adjust. If not, then something is jamming the switch. ... Eureka Smartvac 4870 Bagged Upright Vacuum
How do you reattach the front rollers on hoover elite rewind so that the carpet height adjustment works
... Hoover Vacuums
Dirt devil breeze - height adjustment not working
... Dirt Devil Vacuums
Height adjustment won't work
The height adjustment for the vacuum will only work when the handle is in the released position. The knob will turn easily when the handle is locked upright, and when released you should feel a fair amount of resistance. ... Eureka 4700A Maxima Bagless Upright Vacuum
The height adjustment isn't working...it isn't changing the height at all...how can I fix this?
... Dirt Devil M086700 Vision Bagless Upright Vacuum
The height adjustment on my Bissell 6594-W no longer works, I took it apart and reassembled but still doesn't change the height. Should there be a spring in there? Is there a site with directions on how to fix it? Thank you.
... Bissell 6594 PowerForce Bagless Upright Vacuum
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum
Height adjustment won't work on Hoover windtunnel
In my experience, Hoover height adjustment are "stops" rather than being attached to an axel. Look for something that rould resemble a set of circular steps somewhere in the path the axel would take as it goes up and down. It is usually on the unde ... Vacuums
Getting the height adjustment to work
Is this a piece of **** dirt devil? if so, even when you get it back together the design is so flawed that it will keep breaking the belts, I've already gone through 3 in a week! see my other suggestions to remedy this. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
Height adjustment on power mate doesn't work
... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Hoover auto height adjustment not working
... Hoover Platinum Collection Upright Vacuum
Eureka Boss height adjustment not working so brush stops turning
... Eureka Boss? SmartVac 4870MZ Bagged Upright Vacuum
Automatic height adjust for Eureka 4700A ''Maxima'' doesn't work
... Eureka 4700A Maxima Bagless Upright Vacuum
Capet height adjustment won't work
... Eureka Boss 7601 Bagged Upright Vacuum
Dirt devil automatic height adjustment not working
... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
Bissell 3920 height adjustment not working
... Bissell 3920 Bagless Upright Vacuum
The carpet height adjustment feature on my boss smartvac does not work
What doesn't it do ? ... Eureka Vacuums
The carpet height adjustment is not working on my Windtunnel Bagless U5753-900. What parts are involved that might be broken or missing? Thanks!
... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Automatic height adjuster is not working,it grabs carpet and stops roller
Hi There,Actually usually when this happens, it's usually the belt that causes the brush to stop and not the height adjustment. What happens is, over time the belt will get hot, which causes the belt to stretch. Once the belt stretche ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
We have a Dyson DC28. The brush no longer turns while vacumming the carpets. Also, the lights on the handle to adjust for different heights do not work. Can you help. I see of no way to get to the belt but I don't think it is broken.
Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible. If a repair is necessary, this should be covered by our ... Dyson DC28 Animal Bagless Upright Vacuum
Bissell momentum cyclone height adjustment doesn't work
... Eureka Altima Upright Vacuum Model 2996AVS Vacuum