Having problems with your Sebo K1 airbelt Bagged Canister Vacuum ?

How to access the motor - Sebo K1 airbelt Bagged Canister Vacuum


Answers :

OK, but be warned... it's not so difficult getting the thing apart, but making a neat job of reassembly has been known to drive grown men to despair. And that's because you have to remove the airbelt. But first things first:
1. remove the hose
2. remove the hose-retaining ring
3. remove the flap that covers the green filter.
4. remove the screw beneath that flap nearest to the handle (there's a deeply recessed screw on the other side, but you can ignore that)
5. remove the clip at the back of the machine where the airbelt joins (lever it off carefully with a screwdriver)
6. this is where it begins to get interesting. The airbelt is in two parts - the bulky foam strip and a thin material cover. The cover is held in grooves, top and bottom, running all the way round the machine, by two thin plastic strips around which it is wrapped and which just slip into those grooves. The first challenge is to get those strips, and the covering material, out without damaging them. Just prise one end out with a small screwdriver and work your way around the machine - it's more a matter of patience than anything else. (The second challenge is getting it back neatly!)
7. remove the ends of the foam strip far enough to reveal two plastic clips that hold top and bottom of the body together
8. prise those clips off with a screwdriver.
9. it should now be possible to lift the top cover off. It can be a bit fiddly getting it off over the neck where the hose plugs in, but it does come off.
10. you can now access the motor easily.
11. good luck!

I value feedback, so please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo K1 airbelt Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to access the motor - Sebo K1 airbelt Bagged Canister Vacuum


OK, but be warned... it's not so difficult getting the thing apart, but making a neat job of reassembly has been known to drive grown men to despair. And that's because you have to remove the airbelt. But first things first:1. remov ... Sebo K1 airbelt Bagged Canister Vacuum

Taking off the bumper from A Sebo K1 Airbelt - Sebo K1 airbelt Bagged Canister Vacuum


First, remove the clip at the back of the machine where the airbelt joins (lever it off carefully with a screwdriver). The airbelt is in two parts - the bulky foam strip and a thin material cover. The cover is held in grooves, top and botto ... Sebo K1 airbelt Bagged Canister Vacuum

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.


Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Airbelt k1 komfort 2100 cylinder spool - Sebo K1 airbelt Bagged Canister Vacuum


... Sebo K1 airbelt Bagged Canister Vacuum

Cord reel for sebo airbelt d - Sebo Air Belt K2 Bagged Canister Vacuum


... Sebo Air Belt K2 Bagged Canister Vacuum

Kenmore progressive access motor - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave


... Vacuums

How do I gain access to the motor of an Electrolux 2000 canister vacuum. The air intake on the motor must be partially blocked as there is a loss of suction and the motor makes that high pitched whine like it does when you cover the hose with your hand


Dismantling the vacuum probably won't help much, and reassembling can be a bear. \015\012To check the intake, remove bag and look into bottom of bag well. It there's a filter there, remove it and check intake at bottom of bag well. Clear if t ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I bought a Kenmore canister vacuum, model 116, in April 2007. This morning, the sound of the motor suddenly began to deepen, and I began to lose suction. Normally, if something is clogging the hose, the motor will wind up to a higher pitch, not a lower one. The filters are clean, the bag is empty, and I can't detect anything lodged in the hose. If this were a car's engine, I would say it's "lugging down". Any pointers?


Okay, bear with me. Is it possible you have a suction adjustment, dial somewhere on vac. Check and see and if it does, be sure it's all the way up. Also, try removing hose and run a broom handle fr. one end to the other...BUT be careful not to stretc ... Vacuums

Motor defective will not run - GE 106766 Bagged Canister Vacuum


... GE 106766 Bagged Canister Vacuum

How do I turn it on? - Sebo Air belt K3 Bagged Canister Vacuum


... Sebo Air belt K3 Bagged Canister Vacuum

I just purchased a Sebo Airbelt D canister vacuum. I plugged it in and used it for ten seconds then turned it off, retracted the power cord and now cannot get the power cord out of the machine. Did I not spend enough money to get a quality product? Does anyone have any idea how to get the power cord out without breaking the machine?


... Vacuums

Machine keeps cutting out intermittenly - Sebo Air Belt C2.1 Bagged Canister Vacuum


My Sebo Air Belt C2 Total. The automatic electric cable wire won't stay out when pulled, it just springs back. When I'm hoovering I have to wrap the wire around the small wheels so that it doesn't shoot back in the machine. ... Sebo Air Belt C2.1 Bagged Canister Vacuum

Motor removal - Electrolux UltraLux 2000 Bagged Canister Vacuum


The body on this unit split apart at the bumpers. You will open the front lid and slide the bumpers and the internal slides forward to separate the panels then the rear housing will drop off. At that point you must gently separate the halves by openi ... Electrolux UltraLux 2000 Bagged Canister Vacuum

How do u get muddy grease out of your carpet - Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum


... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

Motor bad - Electrolux Lux 7000 Bagged Canister Vacuum


The best thing to do is to take it to an authorized Aerus Electrolux franchise and have it replaced. They can also check to ensure it is the motor and not something else that would be easier on a budget. ... Electrolux Lux 7000 Bagged Canister Vacuum

Motor needs to be replaced - Kenmore 23313 Whispertone Bagged Canister Vacuum


Are you sure its the motor and not a inline fuse or brushes? How did you conclude it's the motor? ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Burning smell from motor - Numatic HVR200P Bagged Canister Vacuum


I have the same problem. Burning smell , smoke and loud noise!! Any ideas?ThanksCarli ... Numatic HVR200P Bagged Canister Vacuum

Henry Hoover motor noise - Numatic HHR-200 Henry Hound Bagged Canister Vacuum


... Numatic HHR-200 Henry Hound Bagged Canister Vacuum

Our vacuum bag was full and we keep on vacuuming. I believe some lent and hair got sucked into the vacuum motor. We've changed the bag and filters. Now the motor makes a loud noise especially when shutting off. what should we do?


Get a professional repairer to examine it. Even with an over-full bag, dirt will not have got in to the motor if the pre-motor filter was correctly positioned and in good condition. However, the motor may have been damaged through lack of air flow an ... Miele S251i Plus Bagged Canister Vacuum

Overheated vacuum After I finished vacuuming the library last night I changed the bag and shook out both filters and vacuum would not restart. The canister unit felt real warm to the touch but I had been using it a least 1/2 hour non stop. The bag was pretty full but not overly so. It's a Simplicity canister with power head. The carpet is long shag from the 70's Did it just over heat? Thanks Shauna


It normally won't over heat unless the bag is too full, the filters are clogged, or you have have a clog in the hose or down by the brush roll, the inlet may be clogged. Some will restart after a while, some others have a reset to push. If it won't ... Simplicity 7850 Premier Bagged Canister Vacuum

Broken Bag + Dirty Motor = Squealing Vacuum


... Electrolux Guardian Bagged Canister Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0897 seconds