Having problems with your Sebo Vacuums ?

How can the sebo k3 be dismantled to fit a new cable ?

Answers :

I wrote this guide originally for dismantling the Sebo K1, but I believe that with respect to the cable-rewind, the K3 is pretty much identical. So here goes:
1. remove the hose
2. remove the hose-retaining ring
3. remove the flap that covers the green filter.
4. remove the screw beneath that flap nearest to the handle (there's a deeply recessed screw on the other side, but you can ignore that)
5. remove the clip at the back of the machine where the airbelt joins (lever it off carefully with a screwdriver)
6. this is where it begins to get interesting. The airbelt is in two parts - the bulky foam strip and a thin material cover. The cover is held in grooves, top and bottom, running all the way round the machine, by two thin plastic strips around which it is wrapped and which just slip into those grooves. The first challenge is to get those strips, and the covering material, out without damaging them. Just prise one end out with a small screwdriver and work your way around the machine - it's more a matter of patience than anything else. (The second challenge is getting it back neatly!)
7. remove the ends of the foam strip far enough to reveal two plastic clips that hold top and bottom of the body together
8. prise those clips off with a screwdriver.
9. it should now be possible to lift the top cover off. It can be a bit fiddly getting it off over the neck where the hose plugs in, but it does come off.
10. the cable rewind spool is now revealed in all its glory.
11. if you've found my advice helpful so far, here's a final piece... don't try to fit a new cable to the old spool - fit a complete new spool.
12. good luck!

I value feedback, so please remember to rate this response.
Repair Help & Product Troubleshooting for Sebo Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How can sebo X4 be dismantled to fit a new cable

... Sebo Vacuums

How can the sebo k3 be dismantled to fit a new cable ?

I wrote this guide originally for dismantling the Sebo K1, but I believe that with respect to the cable-rewind, the K3 is pretty much identical. So here goes:1. remove the hose2. remove the hose-retaining ring3. remove t ... Sebo Vacuums

New Filters have been fitted on the Sebo automatic XI

OK - I'm a Sebo expert, and we will get to the bottom of this! I need you to do one thing for me: lie the machine on one side, then switch it on and look to see if the brush roller is revolving - KEEP FINGERS and all loose items WELL CLEAR. Does the ... Sebo Automatic X1 Bagged Upright Vacuum

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.

The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi, how can I fit a new power cable. I cannot gain access to the switch area. thanks

... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

Sebo x1.1 fitted with new bag and filter but red bag check light still comes on and then machine shuts off. Any ideas how to remedy?

Without doubt this indicates that there's a blockage somewhere. The two easiest places to look are: 1. on the underside of the machine there's an inspection flap - check in there; 2. remove the flexible hose completely from the machine at both ends - ... Sebo Automatic X1 Bagged Upright Vacuum

Replace power cable on Sebo X4 vacuum claenaer

From memory the plastic part slides up a little, enough for you to access the wiring. I'll try and have look at work tomorrow.Warning though! you need to do this work with the handle laying flat, the screw hole upwards - it may be already ... Sebo Automatic X1 Bagged Upright Vacuum

Fitting a new electricity cord

The cord has been damaged, how do I replace a new one, what parts have to be dismantled to get to the inside of the cleaner ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Fitting a new clutch.

Hi.\015\012\015\012Yes it can be replaced.\015\012Its a lot to explain so try this site It has manuals to do this job.\015\012\015\012http://dysonmanua ... Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

I am a Philips pensioner and purchased a "AZUR EXCEL PLUS 555" steam iron from them many years ago.There is now a fraying of the cable as it leaves the iron with resulting in arcing. There is a detachable backplate on this model which allows corded or cordless use but which cannot be accessed to allow for cable repair by the user. My qustion is can this be repaired or if not can I still purchase a replacement backplate complete with new cable as I this is a great iron and a credit to philips

... Vacuums

I tried to program my Toshiba TV Model 27A43 to a new Universal Remote, because the original Toshiba remote was functioning more+more slowly ( I changed batteries on the original Toshiba remote first) After programing the TV Mode on the new universal remote sucessfully I tried to program the DVD Mode on the new universal remote. After that all our 83 cable- channels are mixed up in their numbers. The numbers only show up to 69 and not to 82 like before. Channels 7-17 show only weak and snowy r

... Vacuums

Miele SES125 electeic hose kinked/collapsed. Can I buy just a hose with a wire in it and put fittings from collapsed hose on new piece of hose?

... Miele SES125 Electric Hose

Poor suction on Sebo x4 - new bag inserted - Sebo X4 Extra Bagged Upright Vacuum

... Sebo X4 Extra Bagged Upright Vacuum

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth

Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

I have a model 1315 sears sewing machine and have a new walking foot that doesn't seem to fit or allow me to stitch.......is there a fix? The walking foot is a kenmore brand and we thought it would fit all kenmores?

I am sure that you realize that it has to be for a low shank machine and that you have to take off the presser foot and use the screw to clamp the walking foot on, and the fingers must be on the take up lever screw. Be sure to check the shank size. ... Vacuums

RE: Miele Art Vacuum When putting on a new bag there's a gap between the bag and the fitting that's a part of the vacuum itself. Is there supposed to be a gap or is there something I'm not doing that will fasten the bag to the fitting?

... Miele ART S920 Bagged Upright Vacuum

My U6616- blew a few parts at once. I have a new push-pull cable --- fine. But the valve arm thing is nuts. I have the new arm piece but for the life of me I can't figure out how that ^*%*^$#$&^( spring goes back in!

I can get you to a parts schematic. http://www.vacsrus.com/cartgenie/pg_u6607900.aspHope it helpsThanks ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.

... Vacuums

Self propel cable broken where can I get a new cable

Whats your make and model? ... Vacuums

Dyson fan belt fitting. i've lost my manual for my dyson animal dc07 and need to fit a new drive belt. thanks in advance, alan

You can see this on utube video. help ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have bought new Hoover bags on two occasions. The first spares I bought were the Xxxl variety and I didn't think they fitted that well. The next spares I bought were the type g megafilt. I still feel like they do not fit that well and the suction power on the vacuum is not as good. I'm I buying the correct replacements? I followed the guidelines on the Hoover bags the vacuum came with. These were printed as the right bags to buy. I only have the vacuum around a year and thought it was brillian

... Bosch BSG71310UC Bagged Canister Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.

... Eureka 431A Optima Bagless Upright Vacuum

I'm trying to use the reverse flow hole on my Miele s712 to blow up an air mattres. None of my fitting appear to fit so I can use the hose. Is there something I'm missing? Is there a trick of the trade? Or am i missing some gear. It's new, out of the box but I just can't get the hose onto the reverse flow. The Poduct is a Miele S712 vacuum dispite what this system has allowed me to enter. ; )


Trying to fix new belt to Hoover Turbo Power vacuum cleaner. Don't see how the belt becomes taut. Fitting it around the roller, there is nowhere to fit the belt to, it just sits loose.

I looked at the user instructions guide online and saw where the 'other end' of the belt should be fitted. It was extremely hard to fit but eventually managed it. Thanks for this solution site. I wouldn't hesitate to use it again. ... Hoover U5396-900 Turbo Power Vacuum

Just tried to fit a new belt to a vax quicklite 2 upright hoover and the belt snapped is there a right way to fit belt

... VAX Appliances Vax X3 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds