Having problems with your Sebo X4 Bagged Upright Vacuum ?

My primary drive belt is wearing the plastic

\015 My X4 sebo primary drive belt is wearing the black plastic shroud and shredding itself at the side and seems to be running off centre away from the motor. The motor is new and the intermediate pulley bearings seem fine. Can you help please.\015

Answers :

Only two possibilities. Either the motor has not been installed properly (it's out of alignment), or the intermediate pulley is out of alignment. Of the two, I'd suspect the intermediate pulley first (except then you'd expect trouble with the secondary belt too...). If you've already solved the problem, perhaps you'd post a comment to let us know what you found.
Repair Help & Product Troubleshooting for Sebo X4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My primary drive belt is wearing the plastic


Only two possibilities. Either the motor has not been installed properly (it's out of alignment), or the intermediate pulley is out of alignment. Of the two, I'd suspect the intermediate pulley first (except then you'd expect trouble with the seconda ... Sebo X4 Bagged Upright Vacuum

Hoover model u5146900 the belt drive is bare metal wears out the belt quickly is there a part that fits over the pin?


The belt drive shaft does not actually wear out the belt unless it has a burr on it, however frequent use does.It should be kept clean and polished with no residual dirt ir burnd rubber. On a department store brand vac you should expect to chan ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

THE BELT DRIVE HAS WORN INTO THE PLASTIC CASE TO THE POINT THAT IT RUBBED ON THE IMPELLER AND BROKE IT , WHAT CAN BE DONE TO REPAIR THIS


You would have to replace the bad parts along with the belt. But you did not give brand and model number info, so can't help more with that info. ... Vacuums

Eureka 5843 belt keeps slipping off of drive spindle.


Tough one. Typically the only 2 things that the belt contacts is the motor drive spindle and the brush roller. Anything else would only be there to protect the belt from debris. Can you turn the brush by hand and see why the belt is coming off? I ... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Dyson DC07 drive belt replacement


Hi.\015\012\015\012The other end of the drive belt the part you cant see goes to a clutch.\015\012The clutch unit has 2 belts one is clutch to motor the second is clutch to brush roller.\015\012You obviously look after your ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

When selecting the carpet cleaning mode, it appears the belt is slipping (due to the noise) over the drive pulley. How do you access the drive mechanism to replace belt or inspect drive pulley and belt condition?


On those units you must replace the clutch assy. you cant just replace the belt. there is also a special tool used to get the new belts on the brushbar. If you would like me to walk you through this repair let me know. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.


Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover u 6401 bought v belt and drive belt the drive belt is to big, the roller will not turn, can someone help?


You will need to get another belt, it's common that the people pulling the parts are so busy, that they sometimes mistakenly pull the wrong part, or the wrong part number was given, even a misprint in the manual. Needless to say, it seems that you do ... Hoover Windtunnel Supreme U5280-900 Upright Vacuum

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

I need a drive belt for Shark vac. Model number UV210BS---The small belt that drives the larger belt for the beater .


... Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Have Hoover Wind Tunnel Sel Propelled vacuum. Had to put on new drive belt. Turn on unit and drive belt slides off the drive spindle.


Look for excessive wear on the unit around the pulleys and their brackets that hold them in place. It sounds like something is just worn out and the belt is either slipping because it is not tight enough or because something is not aligned straight. ... Vacuums

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

Drive belt where is the drive belt?


Go here> http://support.vax.co.uk/power-2-upright to download the manual ... Vax U91-Ma-P Air Pet Multicyclonic Bagless Upright Vacuum Cleaner

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?


I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Where do i find the drive belt for the drive belt for the beater bar on the morphy richards 73310


Try to go to there website ... Vacuums

Belt keeps sliding over on the roller bar and rubbing on plastic parts. Belt is a "U" belt and I am told it should be a "R" belt. Sears sold me a "U" so I will try and find the R tomorrow. What keeps the belt other than tension from sliding onn the roller bar? Could it be that just the wrong belt could cause this??


The 4870 Series uses Part number 61110. It is a "R" Belt. It will appear too be to large. This is normal. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0578 seconds