Having problems with your Sebo X4 Bagged Upright Vacuum ?

I want to release flex from sebo x4 vacuum cleaner to cut back...

\015 Cable has been damaged on sebo x4 , so rather than splicing it and taping up i want to remove , cut back and then reconnect but it isn't too obvious how to get flex out of handle once removed from main body of cleaner ...any suggestions , Thanks\015

Answers :

On the underside of the handle, there's a small screw close to where the metal and plastic parts join. Undo this screw. This will allow you to pull the plastic part out of the metal part - not very far, but just far enough so that you can separate the plastic part into two halves lengthways. That gives you access to the switch, and you should find the rewiring job and reassembly straight forward from there on.\012
\012I hope this helps. If you need more, just post a reply and I'll get back to you as soon as I can. I do value feedback, so please remember to rate this answer.
Repair Help & Product Troubleshooting for Sebo X4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I want to release flex from sebo x4 vacuum cleaner to cut back...


On the underside of the handle, there's a small screw close to where the metal and plastic parts join. Undo this screw. This will allow you to pull the plastic part out of the metal part - not very far, but just far enough so that you can separate th ... Sebo X4 Bagged Upright Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

Sebo vacuum cleaner cuts out ?why


It might be the bag.just check with your local vacuum store ... Sebo X4 Bagged Upright Vacuum

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

I have a Infinity Vacuum Cleaner. Shark Model NV32. I took the wand out to vacuum a spot and now I can't put wand back in. I keep pressing the wand release button when putting the wand in but no good


... Vacuums

Vacuum cleaner I am needing to buy a vacuum cleaner - the flooring in our house is mainly oregon pine with loose rugs. I suffer from back problems and find the cylinder vacuums cause a great deal of back strain. I have been told that an upright vacuum is not suitable for wooden floors - I would appreciate any advice, particularly if u know of an upright vacuum cleaner that works well on wooden floors Thank you


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=517227&thid=728380\015\012Vacuum cleaner\015\012Posted by che9 on Jul 01, 2008\015\012I need to buy a vacuum clea ... Electrolux EL7055A Bagless Canister Vacuum

My SEBO vacuum cleaner keeps cutting out which seems to suggest an dodgy electrical connection...any ideas ?


If it just cuts out then comes back on after a while, it might be overheating. ... Sebo Vacuums

Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don't). I re charge the power, and all seems fine and then it goes back to wanting the filters cleaned. The suction is also not working to full capacity.


Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there ... Vacuums

Hi, the foot pedal has come off my X series upright SEBO vacuum cleaner. How to I fit it back on?


... Sebo X4 Bagged Upright Vacuum

SEBO vacuum cleaner makes a strange noise and shuts itself off after a few minutes. Suction not working when tube is attached, but works with hand-held portion only. Indicator light saying bag is full/clogged is on, but we've cleaned out the bag, cut away any fur/strings that were wrapped on the turning portion, and cleaned out the refuse valve. Not sure what else to do. Thanks!


... Sebo Vacuums

Hello, Could you send me an exploded view of an engine kirby please? My Kirby vacuum cleaner I think for 1997 I think it is garnet, having wanted to change the coals, I do not know the back, is the cause of my request, I contacted a person previously in Bastogne (Belgium) several times which promised to help me but in vain, I count on your good will so I can reassemble it and use it again. In advance, thank you


Try this site out:www.onlinevacshop.com/kirby-G5-parts-manual.phpGood Luck!Jim ... Kirby G5 Bagged Upright Vacuum

Sebo x5 vacuum cleaner


The full bag light comes on when it is getting full or a blockage in the hose or the dirt inlet by the brush roll. Other then that, there is a circuit board called the computer controller, part #5740ER and is giving you a false reading and causing a ... Sebo X4 Bagged Upright Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Difficulty to operate a vacuum cleaner on Smartstrand. I have a Miele which is a great vacuum cleaner. But it cannot move smoothly over this carpet. One's back is under stress trying to vacuum this carpet. The carpet is thick and luxurious and won't rot but it is hell to vacuum.


... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?


It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

I am replacing a foot pedal on an upright Sharp vacuum cleaner-EC-TU2607. I have the broken foot pedal removed from vacuum cleaner proper but it is the removal of the broken pedal from its spring load that has me puzzled. I applied some pulling effort on the pin that holds the spring in place but there doesn't seem to be any give. Is that the correct approach or is there something else that one should be doing first to release some of the resistance by the pin or spring? Thanks!


... Sharp Twin Energy EC-TU2607 Vacuum

How to install the back hepa filter on canister vacuum cleaner. We are not sure which direction the air flows and therefore which way the arrows should point. Should the arrows point into the vacuum cleaner or point towards the outside?


The arrows in this case should point out of the machine. not into the machine. This is because you want the black rubber seal to seal on the machine and force the air through the filter. Good luck. Mark ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Electrolux 5500 The cord on my vacuum cleaner won't retrack. What is the trick to get the back end off the vacuum cleaner? It looks like it was pulled out too far.


Depends on which model you have, but most of them you take off the center section, then you cab get to the 2 screws on top , and there is a screw on the bottom, then the back end will pull off. But I wouldn't try taking the cord reel apart, if that ... Electrolux Lux 5500 Canister Vacuum

The Dirt Devil Featherlite vacuum cleaner throws up the dirt back out. Sometimes the vacuum cleaner doesn't pick up any dirt


You have a blocked vacuum hose take hose off and out side. Push the garden hose from one end to the other, this will push out the blockage ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

I have LG V-3310 Vacuum cleaner of 1400 W. I want to know where will be the dust collected and how can i clean the vacuum cleaner.


Between the top of the carry handle and the body there should be a clip undo the clip open like a car boot take out and replace\015\012R.Carpenter ... LG Vacuums

Hot cord the cord on my vacuum cleaner has been getting very hot the heat is from one end to the other incuding the plug and also where the cord exits the back of the canister please help I love this vacuum cleaner it has been faithful to me for over 15 years!


Likely after all these years that the motor is starting to go bad and draw more amps thasn it should. a new motor at a vac dealer is your best bet. it was likely made by panasonic, so a new panasonic is your best bet, and less $$$than the kenmore for ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1224 seconds