Having problems with your Sebo X5 Extra Bagged Upright Vacuum ?

My X5 doesn't have any functions. I have removed the handle to make sure I have voltage through it (I do), but didn't know if there was a reset located somewhere. Thanks


Answers :

OK - thanks for your clarification. It's really unusual for a Sebo to die completely - it's almost always a discontinuity in the flex that's the problem. The next thing for you to try is: replace the handle, then separate the bag compartment from the base and check that you have voltage at the socket at the bottom of the bag compartment. Or rather, for your own safety, I strongly recommend that you use your multimeter simply to check for electrical continuity between each pin of the mains plug and the various points you are testing, rather than do tests with the flex plugged in to the mains. If you're sure you have continuity on both the live and the neutral wire from the plug to the base of the bag compartment, then the problem is in the base. So next check for electrical continuity between the two contact pins on the base. If there's no continuity, you will have to get the cover off the base (turn it over and remove the four deeply-recessed screws, then turn it right-way-up and lift the cover off). It may be that the carbon brushes in the motor are worn out (they are easily replaced), otherwise (exceedingly unusual) there may be a fault in the circuit board - at which point you may need professional help!\015\012
\015\012Incidentally it occurs to me to mention that, with a discontinuity in the flex, it's often intermittent and will depend on the position of the flex - so be sure to move the flex around quite vigorously while testing, especially just where it enters the handle, before concluding that you have (or have not) got reliable continuity.\015\012\015\012
\015\012I hope this helps. If you have any questions, just post a reply here and I'll get back to you as soon as I can (it would help me to know what Country you are in, and the results of any further investigations you may have made). Good luck!
Repair Help & Product Troubleshooting for Sebo X5 Extra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My X5 doesn't have any functions. I have removed the handle to make sure I have voltage through it (I do), but didn't know if there was a reset located somewhere. Thanks


OK - thanks for your clarification. It's really unusual for a Sebo to die completely - it's almost always a discontinuity in the flex that's the problem. The next thing for you to try is: replace the handle, then separate the bag compartment from the ... Sebo X5 Extra Bagged Upright Vacuum

Riccar 8750 I have a 8750 riccar vacuum and it suddenly didnt want to start. someone told me it has a reset button but I dont know where I could locate it. can you please help?


I have an 8625 and the button is now white not red. Probably fadded. Thanks that was the reset button and it solved my problem. ... Riccar 8650/8625 s Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.


If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

Where is the reset button located on a fuller upright vacumn


It is on the back of the vacuum towards the bottom. ... Fuller Brush FBHD1 Bagged Upright Vacuum

I am currently unsure, it my Dyson DC16 battery is charging as it should. I read all the posts about Powersupply voltage of 28V and defective PCBs. I now need to know from someone who's DC16 is working properly what voltage the battery should have when it is charged. I currently only measure 24.2V in mine. Supposing there are 6 batteries in there with nominal 3.6 voltage each, which would add up to 21.6, I supposed one could charge with up to 25.2V (4.2*6) and once reach lower the voltage ke


Does it stop working real fast ? ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

After over heating the reset button did not reset after a cooling period.where is the reset switch /or fuse located? vacuum is a shark model UV208C


... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don't know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use


If the green light is off, then its time to replace the band. This video shows you how. ... Kirby Ultimate G Bagged Upright Vacuum

I was putting some bedding in a bag for storage and decided to ''**** it down with my dyson hose to fit it in a smaller space. My dyson quit working and now it will not turn on can you please help...??? I know I didn't **** anything up but I can't live without a vacuum!! I have tried the brush reset button but can't find another reset...


There is no other reset. The Dyson will cut out if it gets too hot, but resets itself when it cools. In doing the job you describe, I doubt that you have operated it long enough to cause overheating, or to do any other damage. I suspect the problem i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My tank foamed up into the motor and now the rainbow won't come on. Is there a reset button for the motor somewhere? Will it dry out and reset on its own?


Reset switches are generally for use after a motor has shut off due to overheating. They don't do any good for resetting a motor that has gotten moisture into it. Moisture in a motor will quickly ruin it. Allowing it to dry out on it's own will ju ... Rainbow E series Canister Wet/Dry Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a fake nokia n8 cell phone(basically called chinese). i didnt know about flight mode and turned it on by mistake. now i dont know how to turn it off. menu is not opening and i cant make a cal... plz help me out.. :(


Take the power button should give you the option to turn off airplane mode ... Vacuums

We have a dyson dc14 and the beater bar stopped turning, we cleaned the bar off and checked the belt and it's not broken, I know I called Dyson a year or two ago and they told me how to reset the beater bar motor but I don't remember exactly what I did, anyone know the answer to this??? thanks in advance....


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when the machine is locked upright. When you release the head and pull the handle back this dial should mopve forward to the on position. Once here, the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to know if it has a reset button. we had a power outage and it has stopped working since than. cant find a button to reset it.


Vacuum cleaners do not have reset buttons instead it would have a thermal protection breaker integrated within the motor if the motor overloads it will shut off but will start again as it cools down.Check to make sure the outlet has power in it first ... Vacuums

My Dyson DC07 brushbar is not rotating. I have checked for obstructions. The belt is intact. Is there a reset somewhere within the internals of the unit?


There are two belts on the dc07 one for the brushbar and one for the clutch this video will show you what you need to do ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC14 reset button location


The recommendation about "reset" sort of worked. On my DC14 the button that goes from non carpet tocarpet need to be pushed below the word carpet for the brush to spin. Don't know why it doesn't happen automatically. Before doing this test to see i ... Dyson Ball DC24 Bagless Upright Vacuum

Restart button Where is located that restart (or reset) button that fixed the problem? thanks a lot.


Usually there is a red reset button to push on top of the power head, but some are on the back edge of the powerhead. ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I have a hayden premier supervac central vac system, while working on the switch in for the beater bar, the actual unit has turned off, the green light is no longer lit, is there a fuse on it somewhere or a reset button, i have tried unplugging it and replugging it in, but can not seem to get it to power up now?


Should be a reset on the main unit near the top ... Vacuums

Belt locfation need to know where belt is located so I can change belt


An eureka whirlwind lite /the boss how to open to get at the belt ... Vacuums

My Miele vacuum carpet head will not work. It is an SEB236 Powerbrush and the "reset" light is on when I turn on the vacuum. I don't know what this means! Please help!!


... Vacuums

Hoover tempo It will still **** through the hose but not from the brush-bottom. Can't find a reset button. Vacuum was GREAT and is only about three weeks old. I know it still works because it has plenty of strength through hose, but won't pick up when rolled across floor. thanks! Marian


Sounds like a blockage or belt off in the foot of the vacuum. there is no reset button on this model. ... Hoover Tempo Widepath Upright Vacuum - Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0373 seconds