Having problems with your SewShop.com Singer Model 6412 Millennium Instruction Manual ?

Needle not catching bobbin thread

\015 When sewing the needle does not grab the bobbing thread\015

Answers :

Repair Help & Product Troubleshooting for SewShop.com Singer Model 6412 Millennium Instruction Manual

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.

HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums

I have an expression 2038 and the stitching has suddenly changed so that the top stitching is quite good but the underneath is loose. I have the tension on 4 and have a new straight needle and good quality thread. the underneath or bobbin thread is almost not catching.

If the bobbin thread is too loose, remove the bobbin spool AND carrier.Thread the thread through the tension clip on the holder in the normal way. Hold the thread and lift it. If the bobbin slides down, tighten the small screw 1/8 turn clockwise, u ... Vacuums

Needle not catching bobbin thread

... SewShop.com Singer Model 6412 Millennium Instruction Manual

I have a Singer 144w304 that I cannot get the needle thread to pick up the bobbin thread. I don't know if I am not threading the bobbin correctly out what but I had not had this problem in the past. Everything seems to be in time and set correctly but it just will not pick the bobbin thread up. What can I do?

... Singer Vacuums

While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!

Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.

Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

Bobbin not threading through, spool thread is gathering in bobbin catch and not sewing - just clumps of thread

It would appear to be threaded wrongly. Pull all the threads out, check the visible upper tension discs for broken threads then re-thread top and bobbin, making sure the pressure foot is up when you re-thread. Bobbins should normally turn clockwise ... Vacuums

I have a Brother Nouvelle 1500S and it keeps looping the bottom stitch. I have re-threaded, re-inserted the bobbin, am using the recommended thread and changed the needle? It is still looping the bobbin side stitch?

... Vacuums

I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?

... Continental Vacuums

The bobbin thread is not coming up. I broke a needle and this happen. I have changed the needle twice. cleaned all the lint from the bobbin case. I believe this might be a timing problem is it possible for me to afix this?

Hi, check list:\015\012\015\0121 - Flat side of the needle is facing the back of the machine.\015\012\015\0122 - Threaded machine with the presser foot up - always.\015\012\015\0123 - Bobbin thread is feeding from ... Vacuums

I have a Kenmore 385.19110 model machine, and the straight and zig zag stitches work just fine, but when I follow the directions in the manual to do a satin stitch (which is use the lowest stitch length) it creates a line that isn't perfect, or uniform, and after an inch or two stops catching the bobbin underneath. Have already tried reinserting the bobbin, rethreading the machine, refilling the bobbin, changing the bobbin, cleaning the needle, changing the tension. Wondering if I just got a mac

... Vacuums

Sears kenmore 158.321 sewing machine first broke a needle, needle was relpaced, then next needle bent, needle replaced. Now the thread wont catch in the material . it isnt sewing

Make sure you are inserting the needle correctly. The flat side goes on the left and the thread goes from right to left through the needle. ... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna

... Singer Vacuums

So, I was sewing along and heard a thump...kind of sounded like a louder version of what you hear when the needle hits a pin...but I wasn't using pins. This, of course, lead to the thread jamming so I had to clear that. When rethreading I pulled out the bobbin case to make sure it was seated correctly and found a kind of "v" shaped piece of wire (about the width of a paper clip I guess) sitting loose under the bobbin case. I took it out and threw it away. Still can't pull up the bobbin threa

That part was the hook end of the spring that was supposed to put tension on the bobbin - it will have to be replaced. This is a special flat spring that unfortunately only a repair shop of a dealer has it - you will have to take your machine to one. ... Vacuums

Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee

... Vacuums

Janome sewing machine Harmony 2139 The bobbin thread is not connecting with the needle to make a stitch. We have put in a new needle. Using needle 4 tension

A common problem is if needle is in backwards. The small groove side should be toward the operator. As the needle starts back up after going clear down, a small loop should form on the side of the needle away from teh operator. The shuttle has a p ... Vacuums


Hi,i think the problem is with the needle bar,the alighnment has been distorted internally,i think you should re-align the needle bar in order to restore your machine back to a normal working condition.\015\012\015\012\015\012Thanks and t ... Vacuums

My New Home DX2030 (older than dirt) balls up thread when I try to reverse. I cleaned bobbin holder, hook race and replaced needle, twice. I removed and replaced bobbin and rethreaded machine but no improvement

... Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Janome 6600 sewing machine. bobbin thread is gumming up underneath on a swimsuit knit type material (4 layers). Brand new machine had 1 1/2 weeks. Sometimes material goes down into the bobbin area jammed by needle. What am I doing wrong?

Make sure you're using a polyester thread (I use maxilock serger thread) then a stretch needle, and hold the tails of your thread until you get started into the seam so the fabric cannot push down into the opening on the throat plate.\015\012 ... Vacuums

Singer touch tronic 2001 trying to refill bobbin. bobbin does not turn. needle does not catch.

I'm having the same problem...I followed the directions but nothing seems to be working. ... Singer Vacuums

Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD

... Singer Vacuums

My Singer Futura CE-150 keeps locking up.. The wheel will not turn and the needle locks-up.. I have re-threading and cleaning out the bobbin area but it is still locked up

... Vacuums

My bobbin thread forms massive amounts of loops and a knoty mess. I have tried adjusting the tension and changing the needle. What can I do?elna 3005

Hi\012you just have to open up the bobbin part with a screw driver, take out the bobbin and bobbin case, use a small lint brush clean the whole area.insert the bobbin back once you have finish. There must be a lot of lint in the area it can cause the ... Vacuums

Kenmore YM-40-35 R Sewing Machine Manual (or copy) wanted. If a manual is not available, I'd be OK with instructions for threading the needle and bobbin and any additional details that an expert may have. I think the machine may be a Canadian model number, it looks old, made of metal with screwed in presser foot. Thanks v. much. Elizabeth, [email protected]

Hello,please kindly visit the site below to see the comprehensive instruction with video on how to thread and bobbin your sewing machine.http://www.wonderhowto.com/how-to-thread-mechanical-singer-sewing-machine-224245/wish you ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0259 seconds