Having problems with your SewShop.com Singer Model 9410 Instruction Manual ?
Thread gathering under bobbin
\015 When sewing, becomes "tight" and the thread gathers up on the backside of fabric and underneath where bobbin encased.\015
Here is the manual
Repair Help & Product Troubleshooting for SewShop.com Singer Model 9410 Instruction Manual
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bobbin not threading through, spool thread is gathering in bobbin catch and not sewing - just clumps of thread
It would appear to be threaded wrongly. Pull all the threads out, check the visible upper tension discs for broken threads then re-thread top and bobbin, making sure the pressure foot is up when you re-thread. Bobbins should normally turn clockwise ... Vacuums
Thread gathering under bobbin
Here is the manualhttp://www.singerco.com/uploads/download/440_5_8_10_16_22_dial.pdf ... SewShop.com Singer Model 9410 Instruction Manual
I have a Singer 144w304 that I cannot get the needle thread to pick up the bobbin thread. I don't know if I am not threading the bobbin correctly out what but I had not had this problem in the past. Everything seems to be in time and set correctly but it just will not pick the bobbin thread up. What can I do?
... Singer Vacuums
I have had 226R 20 years. Don't use it much. I have learned to pull slack out of top thread to start so I do that. However, sometimes, as today, it will wind the thread around the bobbin holder and I have to take time to ge it all out clean it up. Is something out of adjustment or what. Sometimes it will sew OK then all of a suden it will start to wind the thread around the bobbin holder again. So I'm confused. Do you have any ideas. Thanks
Hi wwilson63,What make is that 226R?The problem is that the thread is not threaded correctly. You must be very careful and follow directions explicitly.Once you think you have it threaded correctly, sew a few stitches and see ... Vacuums
While using the pin stitch , the machine has started skipping stitches, knocking loudly, the top thread is breaking, sometimes thread knots up on the underneath side. I have cleaned bobbin area, changed needle and bobbin, using quality thread, the last time I used machine worked fine, yesterday when I started sewing I had this mess HELP!
Hi,Please go through the link given bellow to have the resolution to your problem...\015\012http://sewing.about. ... Vacuums
I have a Pfaff Classic Style 2025. After clearing a thread jam in the bobbin area, the machine will not sew. It works without thread, but I think the bobbin case is crooked. The bobbin opening is off to the right, not up, as it needs to be.
My Kenmore sewing machine timing has gotten off. I am sewing a big upholstery project and it starting bunching thread from the bobbin. The thread is so heavy that I had to put some pressure just to get it undone. This happen a few times and then I found it wasn't sewing at all. When I evaluated without the materials in place I could see the needle would catch on the white plastic piece under the bobbin and the thread would not catch on the metal arm. It appears to be off by 1/4 - 3/8 inch.
HelloDisassemble your bobbin case which is realy quite easy, clean\015\012thoroughly with a brush and air, paying particular attention to any\015\012rust that may have formed, and any thread that may have weazeled it's\015\012way into sma ... Kenmore Vacuums
My jenome 4119 will not sew after I took out thread twisted around the inside of the thread takeup mechanism. It but will not pick up bobbin thread and if it does the stitches r inches apart or none a
Cant figure out how to thread elna 1000 lotus sewing machine. also the bobbin keeps getting tangled. if you could send me a diagram on how to thread and bobbin i would appreciate it
I have a Continental Electric portable sewing machine and I can't get the bobbin to thread into the machine to start sewing. How do I place the bobbin and where does the thread need to go for the need to catch it?
... Continental Vacuums
My kenmore sewing machine (Model #385.11803) isn't picking up the bobbin thread. Bobbin thread case isn't turning. HELP!
I just got a new machine (new to me anyway) new home hf106 model. i need to thread the bobbin on the new thead i am using and am not sure where to put the empty bobbin and how to thread it. help!
Janome New Home? Unfortunately, Janome doesn't put the manuals for older machines on their website. Your best bet is to contact your local Janome sewing machine dealer and ask for a "copy" of the manual from them. A photo copy should b ... Vacuums
I have a Brother Nouvelle 1500S and it keeps looping the bottom stitch. I have re-threaded, re-inserted the bobbin, am using the recommended thread and changed the needle? It is still looping the bobbin side stitch?
I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me
Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums
Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna
... Singer Vacuums
So, I was sewing along and heard a thump...kind of sounded like a louder version of what you hear when the needle hits a pin...but I wasn't using pins. This, of course, lead to the thread jamming so I had to clear that. When rethreading I pulled out the bobbin case to make sure it was seated correctly and found a kind of "v" shaped piece of wire (about the width of a paper clip I guess) sitting loose under the bobbin case. I took it out and threw it away. Still can't pull up the bobbin threa
That part was the hook end of the spring that was supposed to put tension on the bobbin - it will have to be replaced. This is a special flat spring that unfortunately only a repair shop of a dealer has it - you will have to take your machine to one. ... Vacuums
I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.
Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums
I have a Singer Model #4562 sewing machine. I am having trouble adjusting the tension. Everytime I try and turn the knob to adjust the bobbin just gets looser. Right now it just snags and gets caught underneath the material and bunches up into a big ball. There is a lot of thread inside the bobbin case that came out of the bobbin and has to be cut out to free the material. How do I fix this mess. I am a novice at this. I have not sewn in several years and would like to sew a few quilts
Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee
I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.
Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums
Sewing machine won't pick up bobbin thread
Open the bobbin case and see if the hook is turning, if it is it is just a timing problem with the hook and needle, if it isn't tuning you may have a broken gear or timing belt.....It eill need to be looked at or adj by someone who repairs them....Da ... Vacuums
My New Home DX2030 (older than dirt) balls up thread when I try to reverse. I cleaned bobbin holder, hook race and replaced needle, twice. I removed and replaced bobbin and rethreaded machine but no improvement
Elna Corina Sewing Machine: the bobbin thread does not pick up. Someone took out the booin case from the machine, and it was never re-installed correctly. Now the thread will not pick up.
I have a janome js1008 limited edition that we perchased for our daughters 14th birt6hauy several years ago and i need instructions on how to thread it & thread the bobbin PLEASE!!
Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st
Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums