Having problems with your Shark Ep604 Retractor Lightweight Stick Vac - Factory Serviced ?
THE BOTTOM FALS OF THE VACUUM MISSING A RED RELEASE CLIP TYPE WHERE CAN I GET THIS CLIP
Repair Help & Product Troubleshooting for Shark Ep604 Retractor Lightweight Stick Vac - Factory Serviced
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
THE BOTTOM FALS OF THE VACUUM MISSING A RED RELEASE CLIP TYPE WHERE CAN I GET THIS CLIP
Mine too!! ... Shark Ep604 Retractor Lightweight Stick Vac - Factory Serviced
Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help
The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?
Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums
The black clip to hold my vacuum bag on my oreck xl signuature plus is missing..can I get a replacement one?
... Oreck Xl Signature Upright Vacuum
Missing bag holder clip bsa 2100 bosch vacuum
... Bosch Canister Compact Plus Vacuum - BSA2100 Vacuum
I bought a Bissell Poweredge Pet vacuum from target. There were no boxed products so I took it off the shelf. The instructions are in the clear filter, but I can't get the vacuum to release and let me get the instructions. How do I ge the instruction pamphlet out of the clear filter portion of the vacuum?
Hi,If you go to this website, http://www.bissell.com/poweredge-hard-floor-vacuum/ you can download a manual for you vacuum. Look on the right side of page for "downloadable documents and click on the manual.This will give you ... Bissell Vacuums
On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug
Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat
It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum
My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.
... Kenmore Progressive Direct Drive 30912 Vacuum
I have a Kirby Heritage 84. Great condition except the part that connects the innerbag is missing. I don't even know what it is called. I can open the vacuum cleaner bottom and see that the part is missing. It should be oval where it connects to the vacuum and then extend into the cloth bag. PLEASE HELP!
The Heritage 84 had two different bag assemblies available. One is a dump-out bag. The dirt simply dumps through the bottom. The other is the bagged style which has a full length zipper to open it. Inside it should contain a "bag fill tube", and a to ... Kirby Heritage II Vacuum
I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"
I have the top of the line kenmore canister vacuum. According to the bottom plate the model nimbler is 116.28015700 I was doing the normal vacuuming and the bag full light came on and the vacuum action stropped. There is still power to the mortorized handle and agitator attachment. Is there some type of circuit breaker reset button for the vacuum function? This unit is probably less that two years old and has had very little use
... Kenmore Vacuums
I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.
Model no. req ... Hoover Vacuums
My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks
Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums
Vacuum getting hot in filter area - Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum
That's not abnormal, unless it's getting very hot. Have you changed the filter recently? If the filter is blocked it will get hotter than normal. the filter should be changed every 4 to six weeks of normal usage. ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum
I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity
Manual I realize it's probably something simple but how do I release the Cyclonic Chamber on top of the Dust Cup lid? I see the red 'open to clean' release button but how do I get down in there to push the release button? Thank you in advance for your help! Best, Christy
Manual > http://www.sharkclean.com/manual/NV22-NV22C-NV22P-NV22T-NV22Q_REV_1008.pdf ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum
I would like to know how i get the very bottom piece off my vacuum off so I can put a new fidder hose on it? The hose is black and it is only about six inches long. its lacation is on the very end of the vacuum but between the end and the piece that gos along on the floor.
You don't have to take the vacuum apart.\015\012Assuming this is an Epic 3500 or similar upright Electrolux:\015\0121. Lay vacuum on it's side.\015\0122. Gently pull hose from power head. It's not screwed in so that should be eas ... Electrolux Epic 3500 Vacuum
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
I just moved into this house and it has a broan cv40-d central vac that i can't get to work it turns on and that is about it i have no owners manuel so i am lost as to what to do any ideas or owners manels available? I can't even get the bottom off after releasing the clasps
The Hoover tempo widepath (blue) vacuums great through the hose but I can't get it to vacuum through the bottom floor/carpet portion. Please help!
Clogged in the vac portion ... Hoover Tempo Widepath Upright Vacuum - Blue
I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?
Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.
If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum
Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]
The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum
Noise I have a filter queen majestic canister vacuum and it was given to me by my landlord,it is the red and black model, but dont know how old it is, its a great vacuum but sometimes it gets this high pitch noise, what could that be?
The high pitched noise could be because the vacuum is loosing airflow. does the red light come on on the top? if it does ot emptythe vacuum, replace the cone filter, the secondary filter, and the batting in the top of the machine. also hook the ho ... Filter Queen Majestic Canister Vacuum