Having problems with your Shark navigator ?

How do I get the roller unlocked

Roller is locked followed the direction to get it unlocked did. Not work

Answers :

Repair Help & Product Troubleshooting for Shark navigator

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.


... Sebo X4 Bagged Upright Vacuum

Roller problem Roller keeps stopping. I've emptied the dustbin. removed the roller to see if it is clogged, but appears to be nothing impeding it.  It stops on a short napped rug, and even on the wood floor.  Is the spool that the roller slips into driven by a belt? Can I get in there behind the spool?


I have 3 Prontos, one in each part of the house. Two of mine had the rollers stop. I figured out the problem and it fixed both. Take the roller out by turning the plastic screw and popping the plate off. Pull all debris off the wheel that turns. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.


... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

Can't get it from Roller Brush Off to Roller Brush On


On some model there is also a plastic tab to unlock the roller brush, check it out. You must also have the right tool installed. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I got a rubber Dog toy jammed in the roller...**giggles** How do I open the roller area to get it out :)


... Kenmore 23513 Progressive Bagged Canister Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

The roller on my power head does not spin consistently. So my vac is not picking up of course. The square end pieces and the rod that goes into the wooden roller seem loose. I tried tightening it but it still is not turning. Can I do a fix with glue or something till I can get a new roller?


... Rainbow E series Canister Wet/Dry Vacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>


I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

How do I change a broken beltoon Eureka altima I can't get to the roller how do I get the piece off


Here is a link to the owners manual which has instructions and a link to the belt you need.Eureka Altima Owner's Guide ... Vacuums

I have the Dyson Ball DC24. I can't get the roller brush to come on...what do I do? I have pushed the red button on the side of the roller but it still does not engage...


Hi its Darran at Dyson.The brush bar re-set switch would normally resolve this, however as you have tried that, please get in touch with our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US) so that we can help resolve this issue for you ... Dyson Ball DC24 Bagless Upright Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I have the belt on the roller, but can't seem to get it to catch. I've turned it clockwise and I can't get it where it needs to be.


Take the nozzle off, make sure the belt is in the center. If this is an old belt, replace it with a new one. Turn the knob until it locks, will only turn one way. Then re-install the nozzle and lock it down. Turn the knob again(will only turn one ... Kirby Vacuums

Hi, I have a Sebo X4 which is almost 3 years old. I haven't had any problems with it until the last couple of days when I notice a slight screeching noise when in upright position, coming from the roller mechanism area. If I slightly push the sebo forwards it gets worse, if I tip it back it stops. If I take the roller out and switch on, there is no noise. I have always been careful not to tip the machine forwards when using the hose, but I recently lent it to a friend whose hoover had broken do


I dismantled the top part of the machine from the bottom and there stuck right down in the bowels of the tubes was a piece of card, a dress label! somehow it was only making a noise when the machine was in an upright position. It took a bit of stretc ... Sebo X4 Bagged Upright Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

I took off the brush roller to clean it and now I can't get the roller to work unless the machine is standing upright. The side that's not connected to the belt keeps falling out.


The solution for your situation is as follows: You need to put the retraining clips on over the arms to properly put them in place You most likely put the retaining clips on too early. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.


Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Roller brush I took the roller off to clean it and now I can't get it back on without the left side just falling loosely to the floor.


Hi,\015\012\015\012you might need to order new floating roller bar holders, they were red on my bissell, they are held in place with two phillips screws on each end, I ended up using large washers to hold those on when my Bissell began m ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together


Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0384 seconds