Having problems with your Shark Navigator Bagless Upright Vacuum ?

Shuts off in the upright position

\015 In the upright\012position the vacuum continues to run..only the roller stops working..this is normal...however..the vacuum now shuts down completely when in the upright position...it has been thoroughly cleaned and the on off switch seems to not operate only if the roller is in operation\015

Answers :

Repair Help & Product Troubleshooting for Shark Navigator Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?


It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

Shuts off in the upright position


... Shark Navigator Bagless Upright Vacuum

Shuts off in upright position and spitting dirt back out


It is a blockage. Dyson cuts off in this case to prevent overload. Also leaking dirt indicates blockage. Strip everything out you can. Remove foot plate on base and check for hair or fibre blockage. it may be small and in an odd place.. seek and ye s ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?


Hi there, it's Jack at Dyson.\012 \012 Like most Dyson vacuums, DC17's main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.


I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dc17 dyson animal shuts off when it is in the upright position. I had just finished cleaning it all out and it started out working amazingly but when I went to use the hose and attachments a second time it would not switch over the suction, just shut off.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson shuts off when returned to upright position and it seems to be not sucking in the down position either


Hi its Darran at Dyson. I would recommend contacting our Helpline on 1866MYDYSON as one of our advisors will be able to run through some simple checks with you.Kind regardsDarranDyson Customer Liaison ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bissel home healthy vac. The brush only turns on for a split second and shuts off. Each time I put it in the upright position and start over, it does the same thing. I thought it may be the switch up on the handle. I replaced it, no luck.


Here is some information about a second Auto Cut-Off Switch near the power switch:\015\012About the only "gripe" I can come up with has to do with the automatic brush shut off mechanism that causes the brush to stop rotating when the unit is mo ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Shuts off at upright position also has lost suction. I have already cleaned the filter


Check for a clog ... Vacuums

Vaccum shuts off when I go to upright position. I checked the hose and also lower attachment and not clogged.


Is the motor running hot? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When I turn on the unit and push on the level that draws the "arm" back, it immediately shuts off. I return it to the upright position and turn it on again and repeat the process. Same thing happens. Took it to an Oreck repair shop (mistake #1) and they couldn't figure out what was wrong. Any ideas?


Seems like there is a short in the unit. it is extremely hard to find kenmore parts. i would probably just go out and buy a new vacuum. Kenmores arent worth fixing. ... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

Hi. We have a Riccar N2100 vacuum cleaner, which has served us well for many, many years. I'd like to attempt a repair on this unit, and looking for advice and/or a parts diagram to proceed. The unit makes a groaning sound when shut off. The sound tapers off in pitch as the motor and beater bar come to a stop. The sound only happens when the vacuum cleaner is turned off in the normal upright position. The sound does not happen when the lower unit and main housing are both laying flat. I took


... Vacuums

Dyson vacuum cleaner - nothing coming into the chamber. shuts off in upright position. I already cleaned the fuzz out of the chamber next to the chamber. Please help. Only 2 months old Thanks, L. Gordon


... Vacuums

No suction in the wand and the vacuum shuts off in the upright position. Just bought a new filter


The wand is clogged. shuttimg off sounds weird. but maybe your cord or something is hitting the off switch. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Eureka 4870 brush won't stop turning in upright position


There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below. ... Eureka Smartvac 4870 Bagged Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc 17 does not work when in the upright position


I had this same issue today, after not being able to find a solution, I took apart the brush area by unscrewing the three simple screws... my belt had a TON of dog and cat hair built up inside it so I cleaned that out and it did the trick. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Vacuum won't **** in upright position, but there is suction from the hose in the upright position


Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums

Kenmore vacuum beltless upright handle shuts off rollers


... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Dyson upright suddenly won't stay in the upright position. It appears that a little rubber piece has fallen out of position.


- Stand behind the vacuum cleaner and look at the right-hand side wheel\015\012- Remove the AI PIPE (it has two purple buttons that you push together to lift it up and out - it looks like a Tuba)\015\012- Lay the handle down and look for ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position


This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

Miele s7000 I clicked my upright into sitting position and accidently bumped the foot release knob. The body fell back and now I can not get it to click back into upright sitting position. Something is now in the way of it locking into place. This happened last year and it was under warranty. it no longer is and I would like to be able to fix it myself in the future. Can you help me? Thank you. Kacee in Oregon


... Vacuums

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis


U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0350 seconds