Having problems with your Shark S3501 Steam Pocket Floor Mop With 5 Cleaning Pads & 2 Quick R ?

The mophead is jammed and I cant get it off. What do i do

Answers :

Stand on the mop head with both feet press button then pull up as hard as you can
Repair Help & Product Troubleshooting for Shark S3501 Steam Pocket Floor Mop With 5 Cleaning Pads & 2 Quick R

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The mophead is jammed and I cant get it off. What do i do

Stand on the mop head with both feet press button then pull up as hard as you canhttp://www.sharkclean.com/manual/S3501_instructions_READABLE_04- ... Shark S3501 Steam Pocket Floor Mop With 5 Cleaning Pads & 2 Quick R

Broken vacuum jammed the rotating brush on a kenmore powermate vacuum cant get it to run properly after clearing the jam

Question; you can't run it properly meaning? The agitator (brush) isn't spinning? If that's the case, then Kazong is right, check the belt. If the belt is fine, check to make sure you didn't damage the bearing of the agitator.\015\012\015 ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help

There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy

The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I got a rubber Dog toy jammed in the roller...**giggles** How do I open the roller area to get it out :)

... Kenmore 23513 Progressive Bagged Canister Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.

Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.

... Hoover Vacuums

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?

Which model do you have.. ... Vacuums

I have a samsung galaxy europa, i get repeated messages 100s of times (no exagerating) i cant get a replacement as i have had the phone unblocked, it was happening before i got it unblocked too, is there any was of getting it fixd?

Glad im not the only one i have the same problem with mine but it just seems to be o2 numbers, i have taken it back to the shop, and they i have changed the sim card about 3 times and they sent it off to samsung and they apperantly changed the handse ... Galaxy Vacuums

What hose gets hooked up for upholstery cleaner. The one that usually goes in front? I cant get my vacumn to turn on.

Hi!You need to take the power nozzle off and attach the thing that looks like a little plastic "cup" with two hooks and a screen on it. This is the intake guard. Attach it to the front. Now remove the cloth bag and put the hose on the hole wher ... Kirby Ultimate G Bagged Upright Vacuum


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

There is a clog in clear tube that sends trash from floor to cylinder. have pulled out lots but cant get really far in there. can I take the hose off somehow and get in there

Try using a hanger and see if you can snake it out there might be a small hose on bottom of power head,i hope this helps thanks ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

How do you put the telescopic wand down? Just got a new dyson 17 and I cant use it cause I cant get the dang wand down..

Make sure your handle is snapped in all the way on to the machine, that will release the clip on the hose to allow for the wand to slide in. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi i hae a star product whipper sniper and i cant get it to go i hae spark i hae fuel but it seems as if there is no fuel getting to cylinder i think it is a problem with my carby the serial no is fcb12071 please help rectify my problem cheers

One thing that you can try is to remove the carb from the unit and spray it down with carb cleaner -- maybe it is blocked (?),,, one more thing to try would be to see if it will fire using ether. there could also be something wrong with the fuel dia ... Vacuums

Help! i have a whispertone 300 model 116 28612790. the retractable cord is jammed & i could only get the front part of the canister open that houses the motor, etc. there are only 2 screws to open it & i can't get it off to fix the cord. hope this makes sense. thank you!

Even if you get it apart chances are it needs a new spring but it requires a special tool to get the rubber molding off that separates the top from bottom and sears repair guys and vacuum shops have them. I would take it to a used vac store and get t ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a handheld steam cleaner model mc1220 and i cant get the lid open .what can i do to get it to open.thank you.

... McCulloch MC1275 Steam Vacuum

I have a rainbow vacuum and it just quit cant figure out how to get to switch to see if it is getting power

Follow the cord up into the vacum it;s probably in the arm. ... Vacuums


Hi - greetings from Scotland!\015\012Im not sure if you mean telescopic hose = do you mean telescopic metal tubes? If so they are readily available on ebay.co.uk I buy from many sellers on there but Hoovermania are one of the best. \015\012\015 ... Philips Vacuums

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther

... Kenmore Vacuums

We have Nilfisk Tempest 1500W bagged cleaner. It just stopped working and I have taken off top cover and all wires/contacts look OK. But power still not getting through I assume. The retractable lead goes into base and cant get to this area. How do I check main lead or perhaps you provide details of serviceman. On North Shore, Auckland, NZ.

... Vacuums

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help

Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Cant get the belt to pick up on the hook when trying to get the head attachment working

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=844275\015\012Generic problem for all Vacuums\015\012Can’t get the belt to\015\012Posted by jltbo ... Vacuums

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!

Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

There is a break in the cord where the clamp is entering the unit of our Majestic IAQS system Filterqueen Lux have tried to get into it but cant seem to get it open! Any ideas?? This unit is approximately 5 years oldish!

Undo the side clamps so that you can get to the dirt below. Grab the handle and remove the top portion of the canister. Take the top portion and to go the table. Remove all the attachments (if they are even attached). twist an ... Filter Queen Majestic Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0632 seconds