Having problems with your Sharp EC-TU5306 Bagged Upright Vacuum ?
How to replace vacum belt on new Sharp EC-TU5306
\015 Vacum isn't picking up any dirt and roller underneatch does not turn.\015
Remove bottom plate and pull brush roll out. buy a replacement belt and follow procedure to put back on. sounds like you have a clogged hose also.
Repair Help & Product Troubleshooting for Sharp EC-TU5306 Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How to replace vacum belt on new Sharp EC-TU5306
Remove bottom plate and pull brush roll out. buy a replacement belt and follow procedure to put back on. sounds like you have a clogged hose also. ... Sharp EC-TU5306 Bagged Upright Vacuum
I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums
I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym
Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
The hoover windmill brand new, new belts not working, replaced new belts with new belts still not working its a useless piece of ****.
... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks
... Eureka Bravo II Bagged Upright Vacuum
My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.
The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums
Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it
Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum
I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the
Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums
Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?
There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum
Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?
... Dirt Devil M084600 Dynamite Bagless Upright Vacuum
Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?
Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum
Hi, The belt of our Dirt devil bagless vaccum broke and we got new belt and replaced it. Even after replacing the belt, the brush is not rotating. Any suggestions please ?
Did you check to see that the beater brush, the brush that the belt drives, is free of debris and moves freely?\015\012When they bind up they can cause the belt to break.\015\012Remove the beater brush just as you do when changing the belt and clean ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?
There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.
I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums
Broan B1396 Model -- Type A -- belt replacement --replacement procedure & new belt
... Broan-NuTone CV353 Central Vacuum
I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1
As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum
Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it
If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum
Belts Burning On our Ultimate G, belts are lasting about 2 uses and they smell and burn off. I am looking at the roller and I can see a slight grove where the belt rides. Is it time for a new roller. I am sick and tired of replacing belts and smelling up the house. Thanks Dusty
Yes, replace the brush roll, the ends or end is probably bad and causing the belt to slip and burn up. ... Kirby Ultimate G Bagged Upright Vacuum
I need to replace the belt I bought a new belt and I can't get the belt back on
On this pagehttp://www.totalvac.com/videos/kirby-vacuum-cleaners-videos.htmthere is a video at the bottom on changing belts on a Kirby ... Kirby Generation 3 Bagged Upright Vacuum
The belt broke on my proheat, I got the replacement belt and got it put on, turned on the machine and it instatly broke the new belt. Any ideas why??
Sound like brush roll is jammed solid .Clean. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I have the Rainbow II Aquamate shampooer and the belt tore. I bought the new belt but can't figure out how to replace it and I don't want to take it apart for fear of breaking it. Is there an easy way to get the belt on?