Having problems with your Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum ?

Vacume wont **** opened it up see nothing wrong HELP

\015 The vacume wont suk at all. I cleaned out the tube and the bruch, it still wont ****.I opened it up to seee the mother but I could see nothing wrong.Th evacume I have is a Sharp Twin energy 12 amp Any one with a segestion please let me know thanks\015

Answers :

If no suction usuallly means a clog, either in the hose and the dirt inlet by the brush roll. Sometimes if the belt is stretched, it won't turn the brush roll under load and it would seem like there is no suction.
Repair Help & Product Troubleshooting for Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacume wont **** opened it up see nothing wrong HELP


If no suction usuallly means a clog, either in the hose and the dirt inlet by the brush roll. Sometimes if the belt is stretched, it won't turn the brush roll under load and it would seem like there is no suction. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t


... Dyson DC25 Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave


... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover Telios TC3202 200W Cord Rewind is jammed - cannot see how to open body of vacuum to look at the source of the problem. Found 4 screws but that did not help - guess you have to prise something open but cannot see where or how.


There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about the others. \015\012Anyway, this is it. The cover is held to the b ... Vacuums

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?


Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

I have bosch forumla vaccum and cord got stuck. It is very hard for me to see the screws to open it. Could somebody help me how to open this safely.


This problem is solved easily after I found the third screw to open the top cover. You will find the third screw under the top cover where the variable regulator is. But be patience, your small mistake can screw up whole system. You will need a torx ... Bosch BSG71360UC Bagged Canister Vacuum

Wont spray i have a bissell pro steam 2x and it wont spray the water out, i have cleaned everything and nothing seems to be working ...please help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I am trying to get to the belt on my fantom cyclone xt, although I am unable to see any screws to remove. I took the rubber bumper off thinking this would be of some help although nothing there either. Can you help???????


Remove the lens covers, bulbs and the foil. under the foil are two screws. remove the screws and the cover lifts off. the motor for the belt is held in with one screw. ... Fantom Vacums Cyclone XT Upright Vacuum

Doesn't work Our home was built and finished in August 07.  The central vac doesn't work.  There is supposed to be a slot that opens in the kitchen where you sweep the dust and it sucks it up.  Also, the mounted unit on the garage wall has a hose that goes up into the house but there is a hole open at the bottom of the unit.  Where can I get someone to help us?  Or, is there an installation manual I can download to see if the builder did it properly.  He stole our solar heater for our pool and s


Has the slot in the kitchen (VacPan) been installed? Or is it just not working? There should be tubing coming into the unit in the garage, and possibly another piece to exhaust the unit to the outdoors, although this isn't always necessary. The intak ... Electrolux Centralux Vacuum

I have a freshield vacum sealer it won't open help please it's new I read the instructions but there's no way I can open without forcing it.Elite FSN .


WE turned it off first,turned it on then repressed the hand push button make sure the lid was shut properly then it popped open.so I started again but made sure that both sides were shut. ... Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

I have a bagless hoover windtunnel. The plastic flap down by the roller wont open! thus nothing will **** into the filter


Go here > http://hoover.com/file/513/ ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hello. My scooba 5800 had a check tank light on. I used a straw on the valve and that fixed the problem. Now the scooba runs like nothing is wrong, but there is no actual cleaning going on! It goes the full cycle, but no liquid comes out. The vac part seems to be working b/c there is fluff in the vac when it's done. Please help!


Hello, Take the battery out and hold the switch down for 30 seconds, to reset the curcuit board, then charge back up for 12 hours. this should take care of it. If I can help future please call @ 1561-848-3387 Thank you, Teresa. Clean Sweep Vacuums ... iRobot 5800 Scooba Vacuum

I have a Sears canister vacume mdl 116.2481290 and I need to replace the wheels. I can't see how to remove the current wheels/assembly. Can you help? B


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a bissell proheat multi surface 2x model 9200-T 08296C. It stopped spitting the water and soap out on the floor, but still sucks from the base and hose. I took it apart to see if anything was disconnected but saw nothing. Please help!


I Had the same problem with my model 79011...take the upright handle apart & you will see a pot-metal rectangular box midway down the lower section of the handle with wires on it & 2 hoses attached. This is the water heater unit. LET IT COOL ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I would like to see how to change the belts on the bissell 8910 pro heat I have looked for hours now. I saw the book but it mentions and shows nothing on how to replace them. Help please.


Turn the vacuum over so that the bottom side is facing you, remove the 4 screws on each side using a Philips screw drive set the screws and the brush cover aside.- pull brush straight out and you will see the gray rubber band.-replace the ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks


This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

I have a Kirby Heritage 84. Great condition except the part that connects the innerbag is missing. I don't even know what it is called. I can open the vacuum cleaner bottom and see that the part is missing. It should be oval where it connects to the vacuum and then extend into the cloth bag. PLEASE HELP!


The Heritage 84 had two different bag assemblies available. One is a dump-out bag. The dirt simply dumps through the bottom. The other is the bagged style which has a full length zipper to open it. Inside it should contain a "bag fill tube", and a to ... Kirby Heritage II Vacuum

Hello! I have a Kenmore Progressive bagless vacuum with the Easy Clean extended life filter. The model number on my vacuum is 34728401. I was vacuuming the carpet when it just stopped running. The dirt sensor light will come on, but nothing else. The belt looks fine, and I don't see anything keeping the beaters from rotating. Help Please!!!


You can have power to the dirt light sensor, but it seems like the motor itself is not using the power supplied. ... Vacuums

Hoover upright soft and light u4266-940 had a pop sound and won't suction. how do I open to see what is wrong and change belt.


Interesting, I just fixed one of thes last Monday for a friend of mine who had the same thing happen to him.To get to see the problem is fairly simple.\015\012\015\0121) Recline the handle of the machine so the whole thing is ... Hoover Soft Light U4266-940 Bagged Upright Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

Motor still runs--sounds like jet engine. do I need a new motor? or is there some sort of muffler that has malfunctioned? vacuum belongs to disabled mom---so trying to do work ourselves--cant afford much. dont see anything obviously wrong--but know nothing about electric motors.


This little vac I think is actually made by Samsung. If it is ROARING and vibrating, either the bearings or suction fan is in bad shape. Remove the lid as if to inspect the belt and see if there is a visible intake opening with a plastic fan rotatin ... Bissell 3590 CleanView Bagless Upright Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0762 seconds