Having problems with your Sharp Upright Vacuum Model 2807, 2809, 2840, 2850, 2860 Brushroll ?

Replace sharp vacum headlight - Sharp Upright Vacuum Model 2807, 2809, 2840, 2850, 2860 Brushroll

Answers :

The light bulb on the sharp upright vacuum is accessed by removing the bottom rug plate. Once that has been removed I believe there is two screws to remove and the light bulb and socket will pull out through the bottom.
Repair Help & Product Troubleshooting for Sharp Upright Vacuum Model 2807, 2809, 2840, 2850, 2860 Brushroll

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n

... Vacuums

My wife and I own 6 IRobots: 1 Scuba 1 Dirt Dog 4 House cleaning vacume models All of them are not working, so I decided to try and solve the problems with two of them: One is a dirt dog and the other a house cleaning vacume Rumba. Given: Battery is fully charged Reaction: I start both of them. They run for about 2 to 3 seconds They come to an abrupt stop as if there is a rock in the gears. Help

Both of them have identical issues? Can you please provide the actual part number of them? It should be on the bottom or inside the battery area somewhere.ThanksTim ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

Replace sharp vacum headlight - Sharp Upright Vacuum Model 2807, 2809, 2840, 2850, 2860 Brushroll

The light bulb on the sharp upright vacuum is accessed by removing the bottom rug plate. Once that has been removed I believe there is two screws to remove and the light bulb and socket will pull out through the bottom. ... Sharp Upright Vacuum Model 2807, 2809, 2840, 2850, 2860 Brushroll

Electrolux 2 in 1 Ergorapido stick Vacuum. Motor runs then cuts out after 3 - 4 seconds. Sometimes it will run properly for 10 minutes so batteries are good. Why does it cut our usually?

If the hand held is working correctly (By itself) try pulling up a little bit on the 4 metal connection tabs on the wand. The connection tabs were not making a proper connection on my unit. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

I have a kenmore canister model number 116.2645083 I need a replacement motor. I was given 2 different numbers: 1. 4147248 2. AC92FAUX200 I can find the 2nd motor, but it doesnt have the 4 wires like the original one. Can you tell me if this is the right motor? Thanks Becky

Greetings from GoVcauum.com,\015\012\015\012Ok, so good news, I have looked up your model number for your Kenmore vacuum and found that your Kenhmore canister takes the motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My plunger (bought in Chile) has 1. a metal filter, 2. a convex (not flat) metal disc with central hole for rod, 3.a metal disc with holes of two different sizes in circles radiating from the centre 4. plunger rod with screw and 5. a spirally coiled wire forming a circle. I cannot figure how to fit these especially the coiled wire. Help appreciated. Thanks

Place the coil in the hole and turn untill reach the desired height. ... Vacuums

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not

Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

1. Bissell Model #7350-C 08249C Carpet Cleaner 2. No soap & water is coming out of machine 3. Worked fine yesterday but isn't working today, we have disconnected it and cleaned all visable places.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have an euro-pro steam cleaner model # sc505 that is about 2 years old. It has only been used a limited number of times, about 3 or 4 times. It now has a tightly sealed safety cap on it and it will not release allowing me to add water to the steamer to use it now. Any tips on fixing it? I'd love to have a products guide to items that are available for compatiability with our sharkie. We constantly see new items available and wonder will that product work with ours?? Thanks!

... Euro-Pro Shark SC-505 Handheld Steam Vacuum

I just got a coralife SPL-165R-JS replacement ballast for my saltwater aquarium but not sure how to hook up the output pins to the wires that go to the bulb. It says pin 1&2 - fila1 and pin 3&4 - fila2, what the heck does that mean? I can't find any wiring diagrams anywhere.

... Vacuums

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?

Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

I have a 13 month old Beldray 2 in 1 Steam Mop Model No. BEL0134ROFOB and it no longer produces steam, Please can you help

... Vacuums

I have a Craftman 5hp snowthrower model 53688501 that will not start. It will fire with gas down sparkplug hole, but runs only untill that gas is burned up. Fuel is present at carb, but I noticed that there are two brass fittings on each side of the carb for vacume lines or something, and they have no lines connected to them. Did I lose the lines that should be connected? Or do I have some other problem. The unit is 4 years old and has the Briggs and Stratton eng model 9A413-0202-E1

This sounds like the carburetor needs disassembled and cleaned. This happens over time and the tiny orifices plug up. Usually from letting gas set in them for extended periods of time and it gums up. If you are not familiar with them, I would take ... Craftsman Vacuums

I have 3 Woods RE1112R remote control outlets (on/off). The power went out so I have to reprogram them. The default setting is #1. How do I program the other two units for buttons #2 and 3? It's been so long I forget how to do it

... Vacuums

I have a 5.5 hp craftsman 20 litre wet Dry vacum . I have lost the manual. & have 2 questions 1) how do I change to wet vacum from dry? Also could i use the wet mode with some water in it and let it run while I am sanding dry wall to catch the dust in the water in the container? Thanks

# 1 myou just take the bag out make sure ytou sponge filter is in place athe top and turn it on the power switch just turns on ,machine ther is no wet dry switch just an empty bagless cannister is all you need make sure the ball outlet in vacumn is w ... Vacuums

We have a zenith dehumidifier model ZD300 & the bucket full light keeps flashing. the percentage number wont go higher than 1%. we have turned it off/on & unplugged it. When we do this it will reset to 40% for about 2 seconds & then goes back to 1% & the bucket full light starts flashing again. The bucket is empty & we have cleaned the filter. We have only had this dehumidifier about 7 months. Please help us.

I've had the same issue with mine. I am a 12 year refrigeration tech. I checked the float switch which would normally cause that indication light. However manually pushing the switch and then checking it with an electric meter that was not the case. ... Vacuums

Nilfisk GM 90 motor bearing Hi I have replaced the motor bearing on the GM 90 model but having problem with re fitting the turbyne I forgot the sequence it has 2 turbines and 4 2 inch washers Can you please tell me the sequence it is fitted Thanks,,,Ps the motor is 100% ok now Peter

... Nilfisk Vacuums

Runs for 5 mins., shuts off for 1 min., starts itself again, runs for 4 mins, shuts off for 1 min., starts itself again, runs for 3 mins.

... Henry Numatic "" Canister Vacuum

Looking for a filter for a singer Model 3HV-100 3 in 1 upright broom vacuum cleaner

... Singer Vacuums

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin

Check the cord to make sure you have continunity throw both leads, check them at the cord reel, there are 2 wires hooked up to it, if not then the cord is bad. Check the swith also, the next cause would be the speen control mounted on the motor, par ... Miele Cat & Dog 326i Bagged Canister Vacuum

I have an Electrolux Oxygen 3 Ultra Canister Model No Rel7020. I am having problems with the On/Off Button and the Bare floor/Carpet Brushroll On/off button. The Carpet On/Off will not work at all. In order to turn the vacuum on, I must press a combination of the first two buttons. Is this an electrical issue

You have a problem with the electrical switches. If you are comfortable with this, take apart and double check internal wiring to make sure nothing was frayed, or disconnected. Make sure it is unplugged. If you know how to operate a multimeter, yo ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie

The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Bissell Proheat Turbo puts out too much water and cleaner and won't **** it back up like it should. Also when I use the attachments dirty water runs out the the hose when I am done. It's used a lot, I shampoo all the carpets about 2 times a month and I shampoo the funiture 1 time a month. I bought it about 3 months ago.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt

Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.

The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0643 seconds