Having problems with your Shop Vac (464-38-10) Canister Wet/Dry Vacuum ?

How do i wire a shop vac to be always on power switch by pass 4 wire


Answers :

Repair Help & Product Troubleshooting for Shop Vac (464-38-10) Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do i wire a shop vac to be always on power switch by pass 4 wire


... Shop Vac (464-38-10) Canister Wet/Dry Vacuum

Qsp shop vac switch wiring schematics


... Vacuums

I need wiring diagram to connect power cord, motor, and switch on a shop vac


... Shop Vac 84M200 Wet/Dry Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Need switch for QPV 11.5 shop vac - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Need shop vac switch for J150A - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Switch for Shop-Vac model QPL650 - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Shop vac wiring diagram motor - Shop Vac 201-13 Wet/Dry Vacuum


... Shop Vac 201-13 Wet/Dry Vacuum

On off switch stopped working 3rd one to do so this one cannot be returned to old ? model QPV10.5b nothing on shop vac site and nothing comes up on Digi-key site really do not want to buy 150.00 vac again but cannot find on off switch! thanks for your help


Use a higher amp rated switch. If this is not available, then solder and insulate the wires where switch should be, then install an aftermarket in-line switch. ... Vacuums

Shop vac 85l450 switch - Shop Vac Vacuums


... Shop Vac Vacuums

My Shop Vac 90L600A is getting electric thru the cord and into the switch, but it doesn't switch on when you toggle the switch from off to on. Is it a bad switch?


Check the othere end of the switch. You may have a brushes problem in the motor. You will have to check the switch while hot - be careful ... Vacuums

I Need an on/off switch for a Shop-vac QPL30 vac?


... Shop Vac Vacuums

I have a model no APL625 shop vac and switch will not turn off. Where can I find a switch


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Wet/dry vacum switch need to replace - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Switch for shopvac H87S550A - Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

I have a Shop Vac Model#92P550A - Ultra Pro 14 Gal. 5.5 H.P. My employee tells me it would go on and off while being used and now it does not turn on at all. I am suspecting the switch could be bad but honestly have no idea whether it is the switch or the motor. Cord and plug are fine.


... Shop Vac (464-38-10) Canister Wet/Dry Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Shop Vac was working fine last time I used it. Now I try to turn it on and nothing. I have cleaned the terminals on the toggle switch. I know there is power to the switch


Try tapping the motor area with a piece of wood or something, damp usage may have seized it up a bit ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum

How do you switch a ridgid 5 hp shop vac from a


... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

Need switch for a shop vac modle qpl650


Ok - heres my story - QPL650 crapped out mid job, checked this post, ordered the switch on the link here, didn't work. \015\012\015\012Called Shop Vac, priced a power unit assembley ($82), took the motor apart and traced the orange wires ... Bosch BUC11700UC Cyclone Jet Bagless Upright Vacuum

Switch for 5.5 hp. 5 gal. hawkeye shop vac


... Shop Vac Vacuums

Shop vac QPL 60 on off switch stays on


... Vacuums

Need switch for Shop Vac QUL 650 - 18 gal. Is there one available??


... Bosch BUC11700UC Cyclone Jet Bagless Upright Vacuum

I bought a shop vac and when I turned it on, it was BLOWING, not VACUUMING. I switched the attachment and it stil functioned as a BLOWER instead of a VACUUM


Put the hose on the other end. it will still blow, but it should work. ... Vacuums

My Shop Vac Series H87 will not power on. It is empty and the filter's clean. I looked under the troubleshooting section of www.shopvac.ca for instruction. They advised to hit the reset/breaker button. However, I don't know where to find that switch. Any suggestions? Thanks! -Spence


... Shop Vac 925-13 Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0412 seconds