Having problems with your Shop Vac 584-06-00 Canister Wet/Dry Vacuum ?

Need a picture or specs of the insides near motor

\015 There are 2 filters up inside and I cant remember where they went. Everything I vaccum blows right back out the 2 vent slots. I have model #QPV 10.5amps 14 gal. 52718-14???\015

Answers :

The big paper fiter attaches to the underside of the big black top piece of vacuum. there is a round plate and a nut you scew on to hold it. a foam rubber filter fits over it.
Repair Help & Product Troubleshooting for Shop Vac 584-06-00 Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need a picture or specs of the insides near motor

The big paper fiter attaches to the underside of the big black top piece of vacuum. there is a round plate and a nut you scew on to hold it. a foam rubber filter fits over it. ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.

Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert

... Panasonic MC-V9638 Bagged Canister Vacuum

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.

... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

I need to rebuild an old GE AC motor model # 5KH35GN106CX (attached to a Gast vacuum pump model 0522) and I need the specs.

... GE Vacuums

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic

... Vacuums

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

My kirby is making a very loud noise and somehow the white fan inside has broken. I have the pieces. What do I need to do? I can't find a vacuum repair place near my location. Can I fix this myself?

What you need to do is a long process of taking apart the vacuum apart. Your fan broke so you are going to need a new one. So go to Kirbys website and look up a nearby vacuum store. Or More recommended a Kirby. It is a long process of taking the vacu ... Kirby Ultimate G Bagged Upright Vacuum

When using a bag inside shop vac, do I still need to cover the motor with foam & paper & ring or can I leave those off?

Keep it on. The purpose is to give you something to clean, a time or two, rather than have to replace the more expensive filter. I know it seems redundant, but all of the pieces filter better than just a bag. Also, if the bag gets any damp or wet mat ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave

... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I just purchased an Electrolux Epic 6500 SR, Model #C102G. I found that inside the cover over the bag. But where is the Serial number? I can't seem to locate that anywhere. Also, in case it breaks, I will need a light gray color on/off switch button located near the front of the canister.rnThanks.

The serial number is on the bottom of the machine. I believe near the front wheels, but can't remember for sure.\015\012Parts can be purchased at any authorized Aerus Electrolux store. You can locate the one nearest you using the below link. ... Electrolux Vacuums

Need a picture of the resevoir inside parts

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hello, I have the BISSELL PRO STEAMER MODEL 8805-1, it's mking rattling sound near the motor, & smells like melting rubber like when the belt is burning. I need check the belt, it's OK. Thanks so much, Susan

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.

You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!

On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

I need the repair specs for a vt820 hibon blower ma thats the new style i need the torque specs the balancing techniques a repair manual would be great and i would be willing to pay

... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Filter queen 95X (1991) Motor is noisy but still work fine. Can there be a loose screw inside ? Can I open the motor and look inside ?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=766802\015\012Generic problem for all Vacuums\015\012Filter queen 95X (1991) \015\012Posted by alexun o ... Vacuums

I have a Kirby G7 and it will run on the low speed setting. When i switch to the high speed it starts to spark and smoke near the back of the motor near the windings. Do i have a motor going bad or is there a simpler fix.

It's probably doing that on low speed too, you just aren't noticing. What you'll have to do is get to the motor. Look at the armature and see if it's scared, missing an pieces, scratched up.. if so, then your motor is shot, throw it away.. If not, if ... Vacuums

I need a wiring spec for oreck vac Mod # XL3600HH

... Oreck Vacuums

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.

If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

Motor My vacuum cut out as I was using it. After some experimenting I found that the circuit reset had gone off. When I tried a second time while near the motor , there was a flash and again the motor shut off. At this time I am guessing that the motor is faulty. The central vacuuming is approximately 12 years old.

If it tripped the reset again, I would probably agree with you. Check out centralvacuum.com for another motor. They aren't the cheapest, but they have excellent support. Good Luck!! ... Easy Flo EF1400 Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds