Having problems with your Shop Vac 925-13 Canister Wet/Dry Vacuum ?

Shop vac 90L400 stopped working won't start

\015 This is the second 90L400 in two years. I guess I will be out of luck if I cannot find the proof of purchase. I would think twice about purchasing this model form Lowe's...\015

Answers :

Repair Help & Product Troubleshooting for Shop Vac 925-13 Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shop vac 90L400 stopped working won't start


I had the same problem with the same model. Turned out to be the thermal fuse on the motor housing, between the switch and the windings. Took it apart and replaced the melted solder with 14 guage copper wire. Works fine! No thermal protection but ... Shop Vac 925-13 Canister Wet/Dry Vacuum

Shop vac 90L400 stopped working won't start


... Shop Vac 925-13 Canister Wet/Dry Vacuum

My shop vac stopped working while vacuuming i looked at everything i could look at and still wont work tried several other outlets checked cable still nothing


Staring from the failrue of the power cord,the main plug,t he main switch each of the sections must be tested for continutiy before we can conclude.\012SInce it is clear case of power failure the voltage must reach the motor,if not back trace t ... Shop Vac Vacuums

I have a Shop Vac (Wet/Dry) Model 5275 (120V 60Hz 6.4A), Peak HP of 2.75 While vacuuming the Shop Vac fell over, stopped working, and would not come back on again. Tried plugging into another outlet, etc., but nothing works. Is there some internal problem that I can fix myself?


... Shop Vac Vacuums

I have a kenmore upright model 116.36933 vac. motor wont stop unless i pull th plug the buttons work on everything else but stopping the vac


... Vacuums

Shop vac lb625 stopped working


... Kenmore Vacuums

My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.


Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum

The steam mop was only used 3 times.stopped working. It has now stopped working altogether. I have only had it for a month. I did not save the receipt because after the third time working I thought it was okay. I am very disappointed and have a hand shop vac of Sharks which has been working for a year. I have been discouraged from buying another one of your products now that the steam mop has quit working after 3 times. I followed the exact instructions how to use it. Model S3101/ 120V 60HZ


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My 2001 miele stopped working Black cannister. I believe cleaning ladies overheated it as the bag was very full and the vac felt warm to touch. I replaced bag and let cool down but it will not start. This has happened before and the vac store said they replaced the cord because it tends to go when it over heats. I have not taken in for and estimate but I fugure it will be at least $150 to repair. Is the another option.


... Miele S548 Bagged Canister Vacuum

I have a miele S712 (2 yrs old worked fine yesterday) - I had been doing some diy work inside and had the vac on just to reduce some of the dust in the air - after a while the vacuum fizzled out. I guessed it had overheated and took it outside to cool down - when I tried to turn it back on pressing the power button gives it power and it starts to **** but it won't STAY on, soon as you release the power button it stops, and the orange bag indicator is showing full. As I have a compressor I took


You have got dust in the micro switch and it is not latching on, if you look at this and clean it, that will solve your problem, however blowing the motir has probably wrecked the motor bearings. ... Miele Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

On off switch stopped working 3rd one to do so this one cannot be returned to old ? model QPV10.5b nothing on shop vac site and nothing comes up on Digi-key site really do not want to buy 150.00 vac again but cannot find on off switch! thanks for your help


Use a higher amp rated switch. If this is not available, then solder and insulate the wires where switch should be, then install an aftermarket in-line switch. ... Vacuums

My electrolux ultra active vacum cleaner wont work, its not even a year old, it will start then stop again and flash E


... Electrolux Vacuums

My shop vac has about 3hrs of usage and it just stopped working. When I plug it in nothing happens. I have no noise or anyting. Is there a fuse or anything and if so how doI access it?


... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

My rigid shop vac 4 gal 5.0 WD4070 wont start


Check elecrical connection, or switch may be bad. ... Ridgid Wet/Dry Vacuums Wd4070 4 Gal Wet/Dry Vac: 632-31653 - wd4070 4 gal wet/dry vac

My Shop Vac QAS60 stopped working while I was using it. Is there anything I can check and/or repair on my own?


... Vacuums

MY SHOP VAC STOPPED WORKING AFTER USING IT FOR A WHILE


If by stopped working you mean that it no longer has any suction, then check the hose for a clog and also clean all the filters.\015\012\015\012If you mean that it literally stopped running, then the most common cause is a faulty switch. ... Shop Vac Vacuums

My miele vacuum has limited suction. it has been to the repair shop twice and when i start it at home it works great for about a minute then the suction stops. Can you help me with this?


... Miele S7280 Bagged Upright Vacuum

Shopvac motor stopped working - Shop Vac Vacuums


Replace the switch. ... Shop Vac Vacuums

Shop-vac model 84em200 won't start


... Shop Vac Vacuums

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.


Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Shop vac shop-vac quit working while in operation and will not turn back on. No strange noise or anything beforehand. Filter had apparently fallen off at some point but on proper reassembly, still not working.


Could have a bad switch, bad cord, or a problem with the motor. ... Vacuums

Vitamix 5000 stopped working. It stops working each time I use it; while blending I first smell a burning smell and then blender stops and will not start again. After sitting overnight it works again next morning and repeat same process. Any ideas how to repair?


It has an internal thermal shutdown. Let it sit for a while and it will reset itself. You can expedite by putting the motor base in the freezer for a few minutes, or by blowing a hair dryer into the base of the motor. ... Vacuums

Shop-vac model 90L550A motor wont run


Yes replacing the link would work, but that would not fix the cause. You have either pulled the wiring to the point of pulling apart the connection or there is a short. Which would be in the way of a grounding effect causing the link to heat and melt ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0861 seconds