Having problems with your Shop Vac 925-13 Canister Wet/Dry Vacuum ?

Shop Vac 90L400 replacement parts

\015 Need motor and motor housing replacment for shop vac 90L400\015

Answers :

Repair Help & Product Troubleshooting for Shop Vac 925-13 Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Shop Vac 90L400 replacement parts


... Shop Vac 925-13 Canister Wet/Dry Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I have a old Shop-vac Stainless Tank QSP CONTRACTOR Wet/Dry Vac Model QPL625 Original #52722-67 Motor arcing and locking up can I get replacement parts?


You can get new motor off the link belowhttp://www.shopvac.com/shopvac-accessories/Departments/Repla ... Vacuums

Parts replacement We have a Hoover Steam Vac that has a broken part #10 in your picture or Part # 37271035. Does this part cover the whole top section of the Vac? Is it hard to replace? Where can you get the best prices on Hoover parts? I have been on Hoovers website and they don't even recognize this Steam Vac. which is hard to believe they don't even recognize their own unit? Thanks Ray


This the hood or top cover. There some screws on the bottom as well as on the top, then it comes off. ... Vacuums

I have a series 90 L - wet/dry shop vac and the caster feet are broke on it can I replace them? If I can where can get the parts from?


... Vacuums

Looking for replacement cap for drain at bottom of shop vac 20 gallon. Any ideas where to search? Part Number?


Contact Shop Vac directly ... Vacuums

Parts for a craftsman shop vac


Hello. The best source of craftsman parts is sears.com\015\012\015\012If they don't have these parts I will be very surprised. regards, Joe ... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Problem: water will not dispense Local repair shop gave verbal diagosis>need both solenoid valves. Found this part on www.nelsonappliance.com $14.95 each. (Shop quoted $98 for repair & parts) Can i access & replace parts? Is there a "how to" video available?


... Bissell 9200 Upright Vacuum

I have an old Shop Vac model 3331.5. This is a 12 gallon 1.5 hight peak shop vac with a detachable blower. After many years I decided to use the blower feature, but have lost the lost the manual. Question; how do I attach the hoses to the blower? The motor has that cap on it the direct the flow of air in one direction and the wide hoses do not fit over it. I may be missing a part, but I would think the directional cap would have to come off anyway.


Remove the cap that directs the air and insert the hose in there. ... Vacuums

I badly need a replacement for the small elasticized grey cloth part (filter??) that fits over the plastic form inside of the hand vac of GE Combiination Vac Bagless System---model 106687, type A. Can you just tell me if the name of that part is the filter? I did find one on a website but there's no image available and I don't want to order the wrong thing. Thank you.


... GE Combination 106687 Upright Vacuum

I have a riccar 500 upright and the axel broke in half. The repair shop says it cannot be repaired without replacing the part. WHere can I get the replacement part?


The repair shop should have all the parts needed. However, sometimes the manufacturer stops making some parts. If this is the case, you may need to try to find one at a thrift store or garage sale and cannibalize it. ... Riccar 8955 Upright Vacuum

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?


I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums

Shop vac 90L400 stopped working won't start


I had the same problem with the same model. Turned out to be the thermal fuse on the motor housing, between the switch and the windings. Took it apart and replaced the melted solder with 14 guage copper wire. Works fine! No thermal protection but ... Shop Vac 925-13 Canister Wet/Dry Vacuum

Getting part My repair shop cannot get the part for my filter queen. It's the plug in the body of the machine that the short plug goes in from the hose. It's been bent. Can I get a replacement part?


Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps. ... Filter Queen Majestic Canister Vacuum

Looking for a replacement canister Shop Vac 2010 1x1


... Shop Vac 201-15-00 Handheld Vacuum

Owner Manual shop vac qsp 10 gallon 6.0 Peak HP, 10 Amp Owner Manual Parts List


... Shop Vac Vacuums

My shop vac blows dust as soon as it's turned on and throughout use. I have changed filters, nothing is helping. What part of my vac can not get wet, or is there a better way to clean out the system?


There should be a cover or sock over the filter,this will stop the dust.the paper filter is the part that can not get wet. if you don't have a cover for your filter use an old sock or something simular to a sock. ... Shop Vac 584-04-00 Quiet Canister Wet/Dry Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I have owned 4 sebo uprite vacs. Every one of them has the same problem. Where the handle connects to the vac it break contact and shuts off and on. It seems the connection between these two parts is very weak. The only answer I get from my local repair shop is


Well you now know the error of your ways, don't buy another!The best fix is to remove the connectors and connect the wires directly together. ... Century 400 UVAC Vacuum

My QSP Contractor Wet/Dry Vac stopped working without any signs of a burned motor. My vac is steel tank, 6.5 hp, model #86776 24. Where can I find replacement parts?


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

DC15 Vac comes on but the head will nmot come on. Local Vac shop said circuit board was burn up,can I repair myself. where do I get parts


HighnTools had posted this solution - try it.\015\012\015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. It was just 2 tiny broken wires \015\012connect to circuit board lead to the beater bar ... Dyson Ball HEPA Upright Bagless Vacuum - Iron/Satin Yellow

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need a part for a Shop-Vac model number 90LN650C. The part number is 7413100 inlet deflector


Http://www.vacshopusa.com/shop_vac1.htm ... Shop Vac Vacuums

I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO


You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0496 seconds