Having problems with your Shop Vac QPMH450 Canister WetDry Vacuum ?

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Answers :

Sorry to read about your problem, I hope this helps you out.

Well you can order a new motor at shop vac, check out this link.
you dont have to remove to check the motor, just connect power to the motor leads


I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful
2 Thumbs - Somewhat Helpful
Repair Help & Product Troubleshooting for Shop Vac QPMH450 Canister WetDry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??

... Kirby Vacuums

Removed and reinstalled motor on Eureka model 6426a. Now power switch position 1 is dead. Power Switch position 2 works fine,

... Vacuums

Vax powa 4000 wet and dry - no suction Both power and pump switches light up. Pump makes clicking noise. Vac motor only powers up briefley when in switched on cindition and mains plug is being inserted into socket.

... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!

... Oreck Vacuums

My Hoover duros s3590 just stopped running. The motor started up and then just powered down and won't start back up. Is this a faulty on/off switch or a motor problem. I'm weighing the +/- to fix or buy a new vac. TIA

... Maytag Hoover Duros S3590 Vacuum (Canister)

Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

I have a Shop-Vac with a 6.5 HP electric motor. The vacuum power is lacking and I think it is the electric motor brushes. Looking for the brushes. The ones I took out have the number 848 stamped on the side.

You can get them off the link belowhttp://store.advancecarbon.com/prostores/servlet/Categories ... Shop-Vac Corporation Shop-Vac 9625410 Wet/Dry Vac 22Gal 6.5 Peak Hp

After using the vac for 10 minutes or so, the motor starts turning on and off with greater frequency the longer I let it run. Eventually it is on and off so frequently that it has no power. Would this possibly be the 24V relay? I have checked the breaker on the unit and it is not tripped. Does the motor have a thermal overload switch separate from the breaker?

No it dosen't. I fix central vacs all the time and relays usally don't do what you described. They either go out all the way and won't turn on or they will trip and you will have to push the breaker back in. What is probably happening is you have a s ... Electrolux Centralux Vacuum

I am looking for a contol board for a miele s143 stick vacuum. The vacuum wont start but when I supply power directly to the motor it spins. I think the switches are OK so I have concluded it is the control board Thanks Don Kenney

You should check the cord and switch's for continuity, the boards are usually pretty reliable, you could check the board for any bad solder joints, at least that would be obvious. ... Vacuums

I have a philips FC9222 vacuum cleaner. When i switched it on today all the lights came on but the motor did not start. all the lights are on and you cant adjust the power up or dow n using the button on the top. the whole thing just looks like it has frozen on. i would be grateful if anyone can help. thank you.

... Vacuums

I need wiring diagram to connect power cord, motor, and switch on a shop vac

... Shop Vac 84M200 Wet/Dry Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

My Shop Vac Series H87 will not power on. It is empty and the filter's clean. I looked under the troubleshooting section of www.shopvac.ca for instruction. They advised to hit the reset/breaker button. However, I don't know where to find that switch. Any suggestions? Thanks! -Spence

... Shop Vac 925-13 Canister Wet/Dry Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.

The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.

If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

Looking for replacment power switch

... Shop Vac Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

No power to head of Kenmore Progressive canister vac

... Vacuums

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0791 seconds