Having problems with your Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum ?

Need 7413100 inlet deflector

\015 I lost the inlet deflector on my model 87L650C Shopvac. The part number is 7413100. Where can I order or buy one?\015

Answers :

Repair Help & Product Troubleshooting for Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need a part for a Shop-Vac model number 90LN650C. The part number is 7413100 inlet deflector


Http://www.vacshopusa.com/shop_vac1.htm ... Shop Vac Vacuums

Inlet deflector facing horisontal. Is this correct?


... Shop Vac 9631227 Ultra Brower Wet/Dry Vacuum

Hello I need a set of rear wheels to my TurboMaster Hoover. If you provide me an Email address, I can send you the drawing + picture. Is it possible to purchase it from you. (I'm living in Israel) Best Regards Zeev Priester 24 Beit Ha'Shita st' PO Box 698 Bat-Hefer 42842 Israel Mobile: +972-(0)52-4299716 Email: [email protected] [email protected] SKYPE: zeev.priester


... Hoover Vacuums

Need parts diagram of holley 0-80559 4150 marine carburetor


... Holley 0-80559 Carburetor 600 CFM Marine

Craftsman 12 gal wet/dry vac #113.177650 - need a filter BAG that fits deflector


... Craftsman 113.177650 Vacuum Cleaners

Craftsman wet/dry has new inlet deflector and which way to face it to pick up dry.


... Vacuums

No user manual/guidelines found in carton. Need some explanation of how best to use the canister, and clarification of the battery compartment 0 to 48 hours sliding switch functionality. Thank you.


You were supposed to be issued with all the pertinent manuals for the machine. Go back to the dealer and demand your manuals. ... Vacuums

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

Ok so, here's my problem. I have a nintendo DSi and I'm trying to connect it to the internet. I've been searching on google on how to connect it. They said that i need wi-fi and some say I don't need wi-fi and some are saying i need a wirelerr router and some are saying that I don't need a wireless router. I'm wondering how I should connect my DSi without a wireless router and without wi-fi.


Http://www.nintendodsi.com/meet-dsi-xl.jspI think you are trying to do the impossible but try this site. ... Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Webpage error detailsrn User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; FDM; AskTbPLTV52/5.12.2.16749) Timestamp: Wed, 1 Jun 2011 21:06:26 UTC Message: HTML Parsing Error: Unable to modify the parent container element before the child element is closed (KB927917) Line: 0 Char: 0 Code: 0 URI: http://www.facebook.com/hoshmend.ali1


... Euro-Pro PT205 Leaf Blower Powerful 12 AMP Leaf Blower, provides 205MPH air speed, Detachable Vaccum... Vacuum

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


Www.searspartsdirect.com ... Vacuums

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?


No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


... Alba Vacuums

I need plumbing diagram for a bissell 9400 need to replace pumpand I need to know what tube goes where on the machine


You can use the lik below and you find the diagrams you need. Their is also the user manual at the same page. Please note that is on lower part of the web page.\015\012Finally at the same page you find and order all the spare parts that you mig ... Vacuums

I need a manual to continue using my bread maker :breadman tr 444I just need a book I have no problem.i just need a manual


You can get the manual on the link below.\015\012\015\012http://www.creativehomemaking.com/download/Breadman_TR444_Manual.pdf ... Vacuums

Need a source and a number for the cannister filter -tried at the Walmart store and now am trying on line... the vacuum label says Eureka ez kleen lightweight upright 12 amp and bagless. We need to get hold of the filters for the bagless cannister sections. We need a source near Belleville Ontario Canada or on line order.


This link may help:http://www.fixya.com/search.aspx?cstm=0&_s=Eureka+ez+kleen+lightweight+upright+12+amp+and+bagless+vacuum+partsJim ... Eureka 421A EZ Kleen Bagless Stick Vacuum

Need to find the belt for the brush. Every sight leads me to drive belts and I dont need that. I need a model number prefferably


Unscrew both bolts that are in plain sight on top of vac above the brush, then remove housing and belt is right there ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?


You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!


... Dyson DC05 Bagless Canister Cyclonic Vacuum

Need to replace power head for blue magic Need


... Kenmore Magic Blue 24195 Bagged Canister Vacuum

I need a break down of the neutral and drive acutator. The assembly has come apart inside. there is a lever that is splind and need timing or positioning prcedures.


... Kirby G5 Bagged Upright Vacuum

Need to replace power cord on Hoover windtunnel need wiring help


Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0382 seconds