Having problems with your Simplicity Freedom Cord - F3300 - A434-0314 ?

Im trying to replace a fan on a simplicity freedom f3300 vacum. HOW DOES THE OLD FAN COME OFF? It seems to be pressed on but I dont want to brake anything.


Answers :

Assuming you have the motor out of the fan housings, check to see if you can move the fan around clockwise/counter-clockwise. If the fan is not moveable, the fan has probably melted to the motor housing. Replacing the motor is recommended as the plastic motor housing under the fan is probably damaged/melted. It could still be fixed but there is a possibility of damaging the housing. If after removing the fan following the directions below be sure to remove/trim any melted plastic away from housing before replacing fan. Not trimming the plastic could result in your new fan melting again to the housing when the machine is turned on. If you have an older model pay careful attention to the carbon brush area, if there are plastic posts holding the carbon brush springs, these are easy to break.

If the fan is movable, remove the nut and washers from fan. Use two large flat head screwdrivers and place them opposite of each other under the bottom lip of the fan between the fan and motor housing. (it might be a little easier if you have an extra pair of hands to hold the motor). With the flat heads in place, push the handles of the flatheads toward the side of the motor where the belt shaft is. If the fan does not pop off rotate the position of the screwdrivers and try again. Pay close attention that the fan washer is installed before replacing your new fan. after installing the new fan, rotate it several times making sure it isn't rubbing anywhere.

If you need any further help feel free to contact me.

Tim
TheVacCenter.com
Repair Help & Product Troubleshooting for Simplicity Freedom Cord - F3300 - A434-0314

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Im trying to replace a fan on a simplicity freedom f3300 vacum. HOW DOES THE OLD FAN COME OFF? It seems to be pressed on but I dont want to brake anything.


Assuming you have the motor out of the fan housings, check to see if you can move the fan around clockwise/counter-clockwise. If the fan is not moveable, the fan has probably melted to the motor housing. Replacing the motor is recommended as the plas ... Simplicity Freedom Cord - F3300 - A434-0314

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

Floor tool wheel will not revolve on dyson dc08 origin vacuum - seems to be jammed. How do I disassemble the unit to fix the problem with the wheel. Everything seems to be clicked in. I do not want to force anything - I might just break it. Any help will be appreciated. Thanks.


Hi,The wheels on the floor tool get junked up with hair pretty quickly, at least they did for our Dyson. The metal peg that holds them in has grooved teeth to prevent it coming out easily, but it will come out if you get a claw hammer an ... Vacuums

I have a unit that is about 4 years old and appears to NOT hold a charge. I know to only charge for 3 hrs max but want to be sure my problem is the $75.00 battery before I purchase one. What is your opinion if I have to keep pressing down on the trigger over and over and over again?


Your battery is losing voltage too quick. It has probably developed a \012'memory'. Dyson claims that their handheld has the best suction out of \012all the handhelds out there. In order to maintain that claim the circuit\012 board will shut off powe ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I have an old Black &Decker 'finishing sander' no.7404-04 ' 120 volts 50/60 Hz type 3 opm 10'000 1.6 amps. i took it apart, BUT' the oscillating mechanism does noy seem to want to "click in". Can you help !!!???!!! Paul


... Black & Decker Vacuums

When using dyson in upright possition does not pick up very well. roller is going round. when you press front to begin hoovering carpets the front doesnt seem to drop onto floor low enough. dont think suction pipe is engaging properly !!!!!!.


Hi Peter, I'm sorry to hear you're having difficulties with your DC07. It sounds as if the internal hose may have become twisted - you should be able to resolve this by removing and replacing it as shown in the video below. Please make sure t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a 4 year old pink dyson that I've loved until recently. It's always been easy to unclog when it wasen't picking up-now it seems maybe a seal problem has occured. The suction is making a funny noise and just not picking barely anything up. I'm getting talked into an expensive Oreck--please help!


\015\012Thanks for your response.First: (This is most likely as you say the suction is making a funny noise.) The DC07 has a short length of clear plastic hose on the underside of the machine. Check this very carefully for splits (pull it ... Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have two lazy spa pumps both of them trip out the electric when the heat button is pushed its only just over 1 year old and i realy dont want to throw it away Kind Regards Peter


Evidently, there is a problem with the heater causing an overload or there was a leak and your GFI is kicking out? Are you able to wire the heater independently through proper safety devices? ... Vacuums

The vacuum does not **** in dirt. It is blowing air instead. Yet when I disconnect the vacuum from the cannister, the suction seems very strong. I took it to a vacuum repairman, and he said that Kenmore sucks and I might as well get rid of it. (He wanted to sell me another one) It is 10 years old, but if I can fix it I would like to try.


... Kenmore 22613 Bagged Canister Vacuum

I want to take the fan impellar off the motor to clean it. I cant seem to get the metal housing off of the motor. Do you have to take the nut off the impellar If so how do you stop the shaft from turning thank you.


Very simply you dont take the fan out of the motor. it was not made to be removed or cleaned because its not supposed o get dirty if your using good bags in the vacuum. the best you can do is blow it out with an air hose. ... Electrolux Epic 6500 Vacuum

I want to take apart a kone dirt devil and i know how it has to be done but i dont have 5 hands to do it. there has to be a tool that presses on the four sides of the case so you can slide the motor unit out. can you help me with this


... Dirt Devil KONE Cordless Hand Vacuum Vacuum

My versatility electrolux vacuum is 2 years old and it has lost its suction, i have replaced the filters and checked every hosing area i have access to, it seems to all be clear. I dont know what else to do, it has a higher pitched whinnig sound when it is on


It sounds like the fan blades have worn away until there's basically no air resistance, thus no air flow/suction. The whine is created by the motor turning at a higher speed due to lack of resistance. \015\012The fan wasn't covered by the wa ... Electrolux Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

Its for a central vac system. I have very low suction power. I've emptied the dirt trap. It seems the fan is working ok, so I guess theres a clog somewhere but I have no idea how to find and fix it. I have no manual on the unit as it was in the house when we bought it. I'd guess its same age as house (19 years old). Any advice would be graetly appreciated!


Usually, low suction would indicate access ports allowing air to enter the system. Easy to test system however. Test vacuum first. Remove intake hose to vacuum ( at the vacuum canister ) and place your hand over intake. You should feel considerab ... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Our Miele vacuum is only 2/3 years old and seems to have given up the gost, our previous one lasted 15 yrs. The machine starts ok and within 4/5 minutes the power drops down and the hoover comes to a stop and it may re-power itself again within minutes, as of today their is no power when the on button is pressed. What do you think the problem is Thank you.


There is a circut board that is going bad and not providing the power to run the motor. You will need to contact a Miele dealer for that part. It is the only board that is in this machine so they should just need a model number in order to get it ... Oreck XL Ultra Bagged Upright Vacuum

I recently bought a chefmate racket bug zapper from target, but can't seem to get it going. I pressed the buttons over and over so it would make it's high pitch sound and then i would know it was charged. never happened. what do i do next? I don't hear anything happening but do see the green light on. can you help?


... Vacuums

No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All


Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I LOST MY INSTRUCTIONS DISK TO MY KIRBY G SERIES AND I DONT KNOW HOW TO DO ANYTHING WITH IT. I JUST REPLACED MY BELT BUT IT DOESN'T SEEM TO BE WORKING AS WELL AS IT SHOULD.


We have a video, online and printed manuals HERE. ... Kirby Generation 3 Bagged Upright Vacuum

My Hoover Linx is not picking up anything. Nothing seems to be keeping the brushes from spinning but they are not working. It is only 3 months old. Fully charged.


I think you have 2 problems:1. The LiNX gets clogged somethings in the head unit and the clog is difficult to see. Remove the head (via the push button). and clean out the clog. I do this with a lenngth of coat hanger wire that I bent a small h ... Hoover Platinum LiNX Cordless Stick Vacuum

I bought an old Juki Baby Lock 418 at a garage sale. It will sew for 3 or 4 inches and then seems to be off timing and locks up. I have no instruction manual. Is there a manual available for this old machine? I would prefer a downloadable manual because I already have money invested in the machine which doesn't seem to work. It was suppose to have been gone over at a repair shop before I purchased it and was told that it worked. .


... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums

My Electrolux Epic 6500 SR will not turn off by pressing on the switch button. I took it apart and removed the switch assy. I can maunually turn it off & on by pressing the rocker arm on the switch assy. It appears that the problem is with the big blue operator button, not the switch assy itself. The button does not seem to press down enough to cause the rocker arm to switch. The button has a "U" shaped wire that presses on the rocker arm and it may have some broken plastic details at the b


WOW !!! Finally You are dead on, absolutely 100%.... good work!!!.Get only a genuine new switch button with spring from an AERUS Electrolux dealer and reinstall. Then carefully reassemble the entire body and wiring harness.Con ... Electrolux Epic 6500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0524 seconds