Having problems with your singer rotomatic fashion maker ?

bobin basket assembly does not move with the wheel movement

due to yhis thread on the bobbin is not picked up

Answers :

Repair Help & Product Troubleshooting for singer rotomatic fashion maker

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?


... Vacuums

Hoover Floormate wheel assembly


In replacing the front wheel assembly, I incorporated a couple of hints from here - first, taking the gray top off by releasing the 6 tabs - 2 front - 2 back - and one on each side - carefully. Then stand the machine up - you need to remove two scr ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Need a front wheel assembly for my Hoover Tempo model u5144-900. I see similar looking Hoover wheel assemblies online for different models, will they fit mine?


The Tempo series cleaners look similar, but are different colors. The wheel assemblies will work if they look identical in appearance to yours. ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating


... Vacuums

My husband took the brush and base assembly apart to clean the unit...when he took the wheel assembly off the small white leveller inside fell off. How do we get this back on??


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Needle rubbing I have a singer pro finish and recently I broke a needle and the lower looper also busted clean off. I ordered the lower looper and replaced the broken one and changed both the needles. Now when I turn the hand wheel and the lower looper moves to the left and the needles descend they pass in front of the looper but when the needles begin to move up and the looper moves back to the right the needles bend back and go behind the looper. Help! Thank You!


... Singer 14CG754.CS Pro Finish Industrial Commercial-Grade Serger

Hoover wheel assembly replace wheels - Hoover Fusion Vacuum Front Wheel Carriage 93001674


... Hoover Fusion Vacuum Front Wheel Carriage 93001674

Replacing Front Wheel Assembly


... Vacuums

The floating wheel assembly stud broke off


You should be able to purchase one from any Hoover dealer. Cost of this part is about $5 USD. The wheels and axles do not come with it, but need to be installed into the new one. Hoover.com you can lookup your nearest dealer. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Robo sweeper The motor runs but the vacuum won't move. It looks like the two other wheels are not moving.


ARE THEY CLOGGED AROUND WHEELS WITH HAIR ,AND TRY SOME W D FORTY OIL , ... As Seen On TV Robo Sweeper

My rear wheels keep poppping off. I've hammered and glued, but they won't stay on. Do I need new wheels or a new axle assembly?


Greetings,\015\012\015\012You may need to just purchase the the little c-clips that hold the wheels onto the axle. Kirby Vacuums actually have a hub cap on their rear wheels that can be removed to access the axle end with the c-clip. ... Kirby Ultimate G Bagged Upright Vacuum

My Viking Husqvarna, model number is 5430, is locked up. The control wheel for the movement of the needle is very tight. I have no instruction book. Does it have a lock on this wheel for transportation? This is a sewing machine my mother had, and she is gone now. Hope you can help. Thank-You.


... Vacuums

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?


ARe you waiting for the error codes?\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:\015\012 ... iRobot Roomba 560 Robotic Vacuum

The top front corner of the rake assembly on our Littermaid Mega box is broken off. Where and/or how can we get a replacement assembly to fix this. Because the piece is broken off, the "wheels" on that side do not like to stay in the rail and the rake doesn't work properly.


... Vacuums

ASSEMBLY HOOVER U5432 WHEEL AND SPRING BACK ONTO VACUUM


... Hoover U5432-900 WindTunnel Plus Bagged Upright Vacuum

Self Propel wheels not enough power to move machine over carpet.


Sounds like the transmission might need an overhaul. Take it to a local vacuum repair shop and have them look at the transmission. ... Vacuums

I need part number of front wheel assembly...


Part number for the wheels [you'll need to order two] 74818a-119n, the axle is part no. 71478 - available at sears 1-800-4myhome ... Eureka 4700A Maxima Bagless Upright Vacuum

Front wheel assembly


This link may help youhttp://www.ereplacementparts.com/hoover-h3030-floormate-spinscrub-500-parts-c-373 ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Install hoover vacuum wheel assembly


... Hoover Vacuums

Hoover vacuum (Legacy 740) with broken wheel axle assembly unit


... Vacuums

Eureka Rally 3977B vacuum cleaner rear wheel assembly


... Eureka 6983 Bagged Canister Vacuum

IRobot is only moving 1 inch back and fort, wheels are clean


You will need to replace the cliff sensors. One one two IR LEDs are damaged. ... iRobot Roomba 560 Robotic Vacuum

My hoover spin scrub machine has stopped scrubbing. It still dispenses and pulls up the water, but the brushes don't move. I've checked the on off button for brush control and cycled it to off and back on, but no movement out of the brushes.


There is a filter on the front right hand side of my F5871-900 Hoover. If you remove the plastic covering and clean that filter (wet finger may do), you're Hoover will begin spinning again! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do I replace the front wheel assembly on the roomba 560. I have the part.


Hi,\015\012\015\012Please find the required process to work with your front wheel assembly for roomba 560 in the bellow mentioned links:\015\012\015\012 ... iRobot Roomba 560 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0239 seconds