Having problems with your Singer Vacuums ?

Is there a setting on a singer machine for ruffling?

Answers :

There's generally a special pressure foot for ruffling. I can't say that I promise your machine can't do it without the ruffling foot, but I've not yet seen one that can.

Repair Help & Product Troubleshooting for Singer Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Is there a setting on a singer machine for ruffling?

There's generally a special pressure foot for ruffling. I can't say that I promise your machine can't do it without the ruffling foot, but I've not yet seen one that can.lp ... Singer Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna

... Singer Vacuums

My Singer Advance #4722 beeps when i try to sew a butonhole. I have the presser foot on. I have set the smaller buttonhole setting but the machine only beeps

... Vacuums

I have a niiken ruffler attachment for my singer machine. Is there a way to expand the bottom guide so that you can put a larger piece of fabric through and ruffle down the center?

... Vacuums

My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?

Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after

... Vacuums

Our beautiful Bernina 730 sewing machine has been stored in the garage in its original case, and that wrapped in plastic, for a few years now. Temperatures have been both hot and cold in the garage, but the environment was dust-free. We have brought the Bernina in, set it up, oiled it as specified in the manual, with the original sewing machine oil. We have correctly threaded the machine and the bobbin thread is up. When we press on the pedal to sew, the machine gets electricity and buzzes

Hello and thank you for using Fixya ....From what you describe there can be only 2 causes...Either the machine is still stuck ..and the motor buzzes cause it can not spin it ..and in this case it needs to be oiled more..and be spun by hand unt ... Vacuums

I have a Yamata GK367B refurbished machine, an older model and the manul is mostly in Chinese and very bad pictures. I need better information about how to thread my machine and to set the tension correctly. I am a professional and need this machine. But it has never worked correctly since I bought it and the company will not take it back. So please help me. Jill G. Arellano

We have no material at all for this brand, sorry. ... Vacuums

Have a spin scrub a couple of years old. Have used it maybe 5-6 times and the green brushes only spin if you take the tanks off and set the machine upside down and push the brushes toward the machine... the second you stand the machine up they quit spinning.

Repace the belt ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums

This was my grandmothers machine and when she passed there was no owners manual so I am not sure how to use the settings on it or oil it properly. I so want to use it cause it was hers but don't want to mess up the machine. She never even got a chance to use it before she passed away. I just have no owners manual. I know how to use sewing machines but this one is older and I don't want to mess it up. this was passed down to me. and a manual would help in so many ways. even if it was sent in a

May I get the manke and model # so I can help you more ... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a singer sewing machine no.66 oscillating hook. looks like serial number 10218349. can you give me an idea of the year this machine came out?

Http://www.singerco.com/support/serial_numbers.html\015\012\015\012\015\012\015\012just google search : what year was my singer sewing machine made.\015\012this ... Singer Vacuums

I have an older Bernina 830 Record sewing machine and I've noticed that it makes a growling noise when I first step on the foot control with the machine in the low speed setting. The noise goes away when the speed picks up. Is this serious? What's the fix?

... Vacuums

I have a Polti Vaporetto Lecoaspira 710. I have filled the tank and set the machine up as usual. When I turn it on the boiler pump runs continuously for a minute or so and then the 'beep' begins and the machine shows that the boiler is empty. Obviously the water is not getting through. We don't live in a hard water area so it shouldn't be 'limed -up'. The manual says to leave it to cool down and then try again. That had no effect. The only answer that Polti 'Service' could give me was to try 'G

... Polti Eco Pro 3000 Canister Steam Vacuum

My Singer Sewing machine (model 6215) is now only sewing in reverse. After pressing the backstitch button, the button seemed to stick in the backstitch position. I was finally able to pull the button out but my machine continues to only stitch backwards. What do I do now?

It's stuck inside. Open it up so you can see inside the bottom, look for the feed dog mechanism and you'll find where length of step is varied, this is where the reversing takes place too. Tapping gently and oiling will free it up.lp ... Vacuums

I have a necchi sewing machine model 4795 and I am having trouble trying to do zigzag stitch for applique. Can you please help me with the settings on the machine. I have tried to use manual, but I still cannot get it to stitch correctly. Thank you.

... Vacuums

Unable to locate needles for Singer Ultralock 14U34 overlocker. Needles required are Singer Cat. No. 2054 10-14. Schmetz Universal are too large to slide into machine. many thanks kaye

Try singer needles 2054 you should be able to find them on line or at a local sewing store ... Vacuums

I have a PQ1500S Brother Quilting/Sewing machine..I am having problems regulating the tension, what should it be set at normally??? I keep having problems with repeated thread breakage, and its a new machine. I have followed all information in the manual. Thanks Theresac57

... Vacuums

I don't know how to thread a Singer sewing machine (very old) Model No 675U App No. N457 Can you email me a picture of the machine with the instructions on how to thread it. Many thanks,

... Vacuums

Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD

... Singer Vacuums

Do you have manuals for a Bissell carpet machine model 1640-6? This machine is about 25 years old. I forgot how to set up soap dispenser

BISSELL User's Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User's Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file.\012Model 1631 is a ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

With my K6 Industrial Singer sewing machine the top thread seems to be too tight. The bottom thread is looping too much on the top of the fabric. The timming is ok. I have checked and rechecked that I have threaded it correctly. It was working great the other day. Please help as we are live out on a property and too far out to get someone out to look at it. Thanks Tania Sorry no category for sewing machines on your list

Hello there, loosen your top thread tension,if it looping on top of the material the tension is way too tight, you will also find changing the thread size to smaller thread, the top tension will also reduce,depending on application a good size thread ... Singer Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4915 seconds