Having problems with your Singer Vacuums ?

Singer Commercial 16-188 S/N G 9466420. Just got new Table, Stand & Motor. The pulley on the Singer does not line up with the belt slot in the table top. Can the pulley on the machine be moved out or is this the wrong table? Table, Stand & Motor was ordered for the 16-188.

Answers :

Repair Help & Product Troubleshooting for Singer Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Singer Commercial 16-188 S/N G 9466420. Just got new Table, Stand & Motor. The pulley on the Singer does not line up with the belt slot in the table top. Can the pulley on the machine be moved out or is this the wrong table? Table, Stand & Motor was ordered for the 16-188.

... Singer Vacuums

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2

Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

Singer 327 lower bobbin thread is wild and loopy after I sew...top stitch fine. Just changed to a large thread spool with the heavy remote base and crook to carry thread to machine and wonder if this changed tension (set at 4 and correctly threaded)? It had been working fine in zigzag but I also went back to reg foot and set stitch width at 0, center needle set. Thanks for your input and help. Deanna

... Singer Vacuums

With my K6 Industrial Singer sewing machine the top thread seems to be too tight. The bottom thread is looping too much on the top of the fabric. The timming is ok. I have checked and rechecked that I have threaded it correctly. It was working great the other day. Please help as we are live out on a property and too far out to get someone out to look at it. Thanks Tania Sorry no category for sewing machines on your list

Hello there, loosen your top thread tension,if it looping on top of the material the tension is way too tight, you will also find changing the thread size to smaller thread, the top tension will also reduce,depending on application a good size thread ... Singer Vacuums

Rick E1, it looks like the Motor Pulley, Elna #440152-20 needs to be replaced on my 722010 model (flat on one side from standing around. It looks like some kind of a set screw which keeps it attached but are you familiar with how to get this item off the little shaft it is on. Also, any idea where I could find a reasonably priced Motor Pulley.

... Vacuums

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after

... Vacuums

I have a futura II 920 machine and the bottom/bobbin tension is not working. no stitches are being made. i rethreaded the machine many times and adjusted top tension, still will not pick up bottom thread. we have no singer repair in our area can you help

I don't know whether I shall provide you this solution or not but the repair manual for your machine is not available. It's available for a purchase specially for fixing bobbin tension.\015\012\015\012In case you don't wish to buy it kindly ig ... Singer Vacuums

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!


Top thread does not pick up bobbin thread, also clicking sound when needle is down under plate, as if it is hitting something. Please help I have a job to do! This machine is new it's a Singer Inspiration Model 4228. It worked just fine until I finished my first sewing job on this machine. I'm hoping you can help me! Thank you, CD

... Singer Vacuums

I have a Singer 500 slant o matic 1961 sewing machine. I ordered a new bobbin winding spring and forgot how to put the spring back into the machine---can you describe where it goes?? thank you Sandra Scott

... Singer Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

I need a manual for my singer 646 sewing machine now. I've ordered one off of ebay but need it sooner.

... Vacuums

I have a Juki serger mo-634de that I am borrowing from my sister in law. She doesn't have the manual, but just got it back from the shop in good working order. I have threaded the machine, and when I manually turn the dial, it appears to stitch properly, but when I press on the pedal, nothing happens. No sound from the motor, no movement with the needles, nothing. Help! (c: Power is working, because bulb turns on.

... Vacuums


... Vacuums

I have a Singer 478 sewing machine and need to replace the top gear on the verticle shaft. Is there a repair manual for doing this. There was not category expert on this so please direct to the correct person.

This is an easy fix. a lot disassembly required, you will need to gain access through the belt side to the singer cover plate,four clips hold it on from the back side. Once that is off, two screw hold small access plate which is under the letters Sin ... Vacuums

The rubber seal strip inside of the vacuum system on top and on the bottom has started coming off. I was wondering if I could reorder this rubber seal stripping to replace on my system. The model number on my system is #91740. MV 261414/1 is another number that was labeled on the back of machine as well. We ordered it off of QVC and the name of this vacuum system is called, Cook's Essentials's Vacuum Packaging System. Thank you for you time. Look forward to hearing back from you soon.

... Vacuums

I want to get my XL-5000 singer sewing machine to work. It does not sew. The top thread will not pick up the bobbin thread for one thing and the other problem is that it gives me a error message saying incomplete threading.

Check if there is any thread in the bottom bobbin and next remove it and give it a good clean in its surrounding area.Oil surrounding mechanism carefully and manually push the top needle in and watch the bobbin spinning a see if it tried to pick the ... Vacuums

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?

Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like

I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the

If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums

The top motor on my Nutone CV-750 quit working

... Broan-NuTone CV750 Central Vacuum

I have an elna 3007 machine. Our service man died and I need help with the tension. I can't get the top tension number to change off zero. when I free motion, all I get are loops top and bottom. I have adjusted the machine the best I can but still have the problem. I'm in the middle of a quilt and could use some help.

... Elna Vacuums

Motor problem machine is smoking/burning smell coming from the bottom of the machine. Motor still turns but doesn't make much sound; and soulution won't squirt. The model # is 1970

I had to throw the machine away before it burned my house down. There is no way to fix it; had to replace it. ... Bissell 1770 Quicksteamer II Upright Vacuum

Elna TX Electronic machine. Top thread gets tangled in rotary hook when straight stitching. Top thread is also found attached to bottom of fabric when removed from machine. Can you help please.

Try a different type of thread for this operation. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4477 seconds