Having problems with your Stainless Steel Brakes SSBC 28146 Electric vacuum pump kit. For when ?

Issues with SSBC electric vacuum pump 28146

\015 My 68 Impala 2DR Fastback has a professional 434 sbc puts out 615 H.P. 598 torque after installing a Mass Flow port injected RFI. It had excellent throttle response, increased H.P. and greatly improved brake response. Thankfully I noticed while on the highway my oil pressure dropped below 20 psi bouncing from 5 to 20 very dangerous for possible seized engine. Luckily a mechanic I knew and used was very close and able to work on the car on his off hours. He insisted on installing a SSBC vacuum pump 28146. Before he had the car it was not necessary. He bled the brakes, dropped the oil pan as the tip had broken off, it was intact no damage i purchased an expensive reusable gasket. It appeared that the builder didn't tape off areas that should not have ever had paint on it subsequently every place painted started leaking. All was supposed to be fixed, I switched the NGK plugs to the colder #10's. Basically the car will spark start rev to 3000 rpm's then die. if Im lucky I can feather the accelerator and get it to go into gear, now the car bucks and has tremendous blow back through the air filter. The Mass Flow creator originally a Ford product has systems for most engines and cars. It is his very strong opinion that the PCV system has a massive leak somewhere. Possible that the Mass Flow could have been damaged. He is pretty confident however is the leak. I'd appreciate any input before spending money wastefully.\015

Answers :

Check the internal vacuum pipes of the electric vacuum pump. For more information, please visit computer tuition.
Repair Help & Product Troubleshooting for Stainless Steel Brakes SSBC 28146 Electric vacuum pump kit. For when

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Issues with SSBC electric vacuum pump 28146


Check the internal vacuum pipes of the electric vacuum pump. For more information, please visit computer tuition. ... Stainless Steel Brakes SSBC 28146 Electric vacuum pump kit. For when

BOSCH 0 132 006 345 - Bosch Vacuum power supply pump mercedes benz 0 132 006 345


... Bosch Vacuum power supply pump mercedes benz 0 132 006 345

Bosch Vacuum power supply pump mercedes benz 0 132 006 345


... Bosch Vacuum power supply pump mercedes benz 0 132 006 345

I have an Electrolux Oxygen 3 Ultra Canister Model No Rel7020. I am having problems with the On/Off Button and the Bare floor/Carpet Brushroll On/off button. The Carpet On/Off will not work at all. In order to turn the vacuum on, I must press a combination of the first two buttons. Is this an electrical issue


You have a problem with the electrical switches. If you are comfortable with this, take apart and double check internal wiring to make sure nothing was frayed, or disconnected. Make sure it is unplugged. If you know how to operate a multimeter, yo ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.


Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Aquamate basin pump does not work. Used it 3 times, stored it for a year and pump does not work. Looks like a reliability issue. Is this product defective for everybody? I saw an ebay listing for the basin that states "the pump works." Looks like I am not the only one with this problem if he has to mention that the pump worksl How do I get a basin with a working pump? gap920


Hmmm............ looks like the impeller is already stuck from a year w/o using it!\012\012\012I suggest if u could open it and spray some penetrating oil on the bushing of the pump motror and the impeller, force the motor to turn m ... Rainbow E series Canister Wet/Dry Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Rule 1800 Pool Cover Pump With Leaf Protector 110v not running. Pump had a partially severed electrical cord which I repaired. I have cleaned out the pump for debris (took off outer parts). I still get nothing when I plug it in. Impeller is somewhat hard to turn but I can find nothing impeding it. Thoughts?


Most likely the shaft bearing is seized up and not allowing the impeller to turn. Pull the bottom odd till you can spin the impeller by hand and use some penetrating oil around the shaft turn it by hand a few times and then with it still apart plugg ... Vacuums

Salton vacuum bag sealer The vacuum pump does work well but no vacuum in the bag. Thanks


... Vacuums

My Shop Vac (Brand) Mdl#934-16-11 keeps shutting off while I'm dry vacuuming. I can turn it back on then it will shut off again. The filter is spotless, so that's not the issue. There isn't any reset buttons. The only thing I can think of is that the float for wet vacuuming is somehow being sucked up causing the the motor to be tripped off. The vacuum is only about a year and a half old and used only sparingly. Help!


... Vacuums

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis


Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums

How do i turn the pump on to pump out the water this is a 16 gallon 5.75 peak horsepower wet dry vacuum.


If you want to get water that's in your vacuum, OUT of your vacuum, you simply need to remove the top and dump the water out. As far as I know, the Shop-Vac 962-16-00 won't "pump out" any water that's in it.If you want to pump water from ... Shop Vac 962-16-00 Ultra Pro Canister Wet/Dry Vacuum

Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.


Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum

I have a iRobot 4150 and have recently experiencing performance issues with the vacuum. Recently, it started stopping about a minute after you turn it on. I thought maybe the battery was the issue, but I bought a replacement. It has worked well for the past 6 months. While it's running it sounds like it is going to die, even though it is fully charged. Any ideas?


Yes, a common issue with the cleaning head module, chm. You will need to diassemble the Roomba and remove all debris from the CHM. Also take a look in its gear box. ... iRobot 4150 Roomba Vacuum

I have a Kenmore DuraPower Dual Cyclone Action 12 Amp that just randomly stopped right in the middle of vacuuming. I assumed the plug had come out of the wall so I went to check and this wasn't the issue. I tried multiple outlets and that wasn't the issue. I made sure nothing was stuck and there is nothing stuck. Nothing happens when I press the red "ON" button. What could this be? Thanks!


... Kenmore Vacuums

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Bissell healthy home vacuum will not turn on. I have checked everything on the vacuum. All the filters are clean and there are no clogs. I have had it for 10 months with no issues until now.


- The handle may not be installed properly, causing a loss in the power connection. Remove the handle completely. Slide the handle back into place on the lower section of handle and tighten the screw. ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

Vacuum stopped in middle of vacuuming our carpet. Would not startup at switch. Tried other electrical outlets wondering if this was the problem and checked breakers, but it still did not go back on.


2 guesses.... One is that you vacuumed up a pice of cord or sting that got wound up on the roller (if it's that tyme of machine, and NOW everything's completelt "loced." Cure: look at the brush roller and "unwind" the cord or string.\015\012 ... Vacuums

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Kenmore Vacuum 116.35622: Need to know how to attach the board to the vacuum that is supply the power to the motor. (need the electrical diagram) email: [email protected]


... Vacuums

Kirby vacuum there is a way to usr your vacuum as a pump how do you do it


The Kirby air flow can be reversed to become a blower (not pump).\015\012This is ideal for blowing up low pressure items such as air beds etc.\015\012Take off the complete bag assembly by twisting at the bottom and unclip at the top. ... Kirby Ultimate G Bagged Upright Vacuum

New panasonic ez bare floor vacuum mc-ul675 is top heavy. when I have it standing upright if always falls backwards. No matter what I try it still falls. Great vacuum other than that issue


... Panasonic Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1139 seconds