Having problems with your steamvac ?

the steam vac stopped picking up water.there is no dirty water. I t did pick up in one room only. can anyone help

Hoover steamvac. This product is brand new and stopped working already.

Answers :

Repair Help & Product Troubleshooting for steamvac

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On off switch stopped working 3rd one to do so this one cannot be returned to old ? model QPV10.5b nothing on shop vac site and nothing comes up on Digi-key site really do not want to buy 150.00 vac again but cannot find on off switch! thanks for your help


Use a higher amp rated switch. If this is not available, then solder and insulate the wires where switch should be, then install an aftermarket in-line switch. ... Vacuums

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.


Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.


Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum

Took Roomba apart to clean and now the pick up brushes start and stop during cleaning. The vaccum is clean but will not constantly spin. Runs great but pick up brushes start and stop. Is there a number for Roomba? Warranty? This one is less than one year old.


You can go to www.iRobot.com . This is the roomba website. You should be able to find replacement parts, customer support, videos or the Roomba product, and more.\015\012When y ... iRobot Roomba 530 Robotic Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1


As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Dyson 28 airmuscle... carpet level selectors will not stop blinking... I have tried all selectors to see if an adjustment helps It has not lost section but the blinking light tells me something is up... I have two vaccumes one for upstairs and one for downstairs. all same carpet in the house and I use the medium pile and only one of the vaccumes is having this problem


... Dyson Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???


Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum

I have a dyson DC23 and the turbine head will not turn anymore can anyone help on how to reset. I have cleaned it and there is no blokage its just stopped? Please can someone help


Pull the plunger into the ''out'' position for vacuuming carpets.For vacuuming hard floors push the plunger into the ''in'' position to stop the brushbar spinning.Refit the tool onto the ma ... Dyson DC23 Bagless Canister Cyclonic Vacuum

I have a dyson animal dc24. It is 7 months old and has stopped working. The hand tool is working fine but when I insert it to engage in normal vaccuming the suction stops. I can hear a strange air sound. Also the brush is spinning but it is not picking up. I have taken it apart and checked for a clog but I don't see one. Any advice?


Hi there,I'm sorry to hear your DC24 Animal isn't picking up as well as usual. Although I note you've already checked for blockages, it sounds as though this is likely to be the cause of the issue.To locate and remove any blockages, p ... Vacuums

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!


I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.


... Vacuums

I am looking for a Hoover Steam Vac Bare Floor Attachment, Part #90001331. I found one in the US for $8.95 but by the time I paid shipping and handling it would cost $91.77, a little ridiculous. I am looking for one in Canada. Can you help. I have heard Hoover has been bought out and parts are very difficult to purchase. I bought this 1 month ago and I'm sorry I didn't know this prior to purchasing.


Hoover Bare Floor Attachment F5XXX from Usavacuum.comIt is $6.99 and shipping should cost you le ... Hoover F5906-900 Upright Steam Vacuum

I own a hoover steam vac model f5915-900 and i currently have two problems. 1. the brushes are spinning at a much slower speed. 2. the steam vac is not picking up the water it leaves on the carpet. Please help Josie


The reason the brushes are not spinning is because the belt is slipping, the belt is the bad that connects to the brush to a shaft that makes it spin. Next problam is it is probobly clogged. so water is not going through all the way ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM


Http://www.vacmall.com/supplies.asp?Brand=Fantom&Model=Cyclone+XT ... Fantom Vacums Cyclone XT Upright Vacuum

HOOVER VACUUMS MY MOTHER'S WORK, MERRY MAIDS, USES ALL HOOVER VACS. THEY ARE LIGHTWEIGHT-UPRIGHT-BAGGED VACS. I TRY TO FIX THEM WHEN THE MAIDS BREAK THEM; BUT, I'M HAVING PROBLEMS WITH A BURNING SMELL AND ONE MOTOR EVEN SMOKES. I'M NOT SURE THE MODEL. CAN YOU HELP? THANK YOU.....


Go to thehooverstore - this site lists a whole bunch of hoover machines, exploded diagrams and parts lists. ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

Bissell bagless sweeper sucks up dirt but will not put dirt in the canister cup. It will pickup until it clogs, then it will stop picking up dirt. It will really hold quite a bit of dirt before it stops completely up. Thanks for any help.


I had the same problem, called Bissell over 10 times! They send me 3 plastic inserts for the dirt chamber, not the problem. I solved it by throwing the Bissell away and buying a Eureka bagged vacuum, no more problems. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Help!!!! i have an older model of the dirt devil bagless quick vac. and it has been working great, just last week i was vaccuming my bedroom and i accidentally sucked up a string belt that goes with one of my capris. and today i emtpied out the dirt cup but it seems the the string belt that was sucked up is not within my reach and whenever i start the vaccum i get this distinctive noise that i've never heard before. help.


It's likely wrapped around the brush\015\012pull out the roller and un tangle it ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

Epic 6500 vac stopping for no reason


Could have a problem with the cord or the motor. ... Electrolux Epic 6500 Vacuum

How to... I have a Black and Decker 900 watt hand vac. I can't seem to find my manual i was wondering how the attachments go onto it..If anyone could help that'd be great!!


My HV8000 is a 900 watt - not sure if it's what you have or not, but it you go to blackanddecker.com and click on customer service (then parts or replacement parts & manuals), it will pop up a window where you can type your model number (or other ... Black & Decker HV8000 Handheld Vacuum

I have a one year old Beam central vac. It has supervalves. The handle (connected to the hose stopped turning on the unit. The handle still powers the brush but no longer turns on the suction?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566201 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0742 seconds