Having problems with your Sunbeam Vacuums ?

Sunbeam Cafe series coffee machine em6910. Even after relacing the group head seal it leaks around the basket when expressing. I have followed all the instructions and tried different grinds and levels in the basket. The seal shows good signs of even contact.


Answers :

Repair Help & Product Troubleshooting for Sunbeam Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sunbeam Cafe series coffee machine em6910. Even after relacing the group head seal it leaks around the basket when expressing. I have followed all the instructions and tried different grinds and levels in the basket. The seal shows good signs of even contact.


... Sunbeam Vacuums

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?


... Vacuums

I love my Keurig.....I have recommended it to many of my friends...3 of my friends asked if they could use their own coffee (and not trying it I said yes)...I have been told that the coffee grinds come out and are in the machine. I thought maybe they used too much coffee (but they tried various amounts)so I tried it myself and sure enough the grounds were all over the place. Even if I half filled the container....PLEASE HELP as they are cursing me...


Dont try it ... you will cause lots of troubles. Ops, you already tried it ... There is a special filter in the cartridges. I dont think you can replicate the cartridge.\015\012\015\012Thanks for visiting today. ... Vacuums

Will not turn on. tried different outlets and replaced bag. came on for a second then stopped working even though switch was on. trying to only use hose.


It is probably clogged up or its suction motor is burned up. Hop this helps!?\012\012\012Please rate solution - Thanks. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.


Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum

My Hoover Pet Cyclonic upright stopped working while I was using it. The bottom felt really hot so I emptied the canister & laid the vacuum down with the bottom in the air to cool off & went back in an hour or so, I even tried a different plug in but it still won't turn back on. I don't know what else to try.


This just happened to me. Any solutions or insights? I need to know asap. ... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

How do you clean the inner mechanisms of the steamer. I tried the instructions in the manual which basically said to put fresh water in a few different times to remove the scales. Can I use a vinegar


... Rowenta IS9100 Steam Cleaner

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I had plugged it in to use it, turned it on and instantly it made a pop sound, smelled of electrical, and would not turn on after. i even waited for a while let the smell go away and tried a different plug in the house and still no operation of any kind. Is there an internal fuse that i could check on this? where is it located?


Sorry there is no fuse in the vacuum. It sounds like there is a short somewhere when they manufactured it. There is no way to fix yourself you will need to take to a repair shop\015\012\015\012Good luck ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me


Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

My Ultra Lux 2000 beater bar still does not operate even after following manufacturer's instructions, per owner's manual. The vacuum shut off automatically when I accidentally caught it on plastic bag.


Make sure all threads, hair, and similar stuff is removed from brush, then try again.\015\012Did you try switching the power nozzle switch off then on?\015\012Does the power nozzle motor run? If not, and you've pressed the reset button, ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I am trying to use the hand tool but the suction isn't working. It spits out the soap and water but it isn't sucking up the water. The machine is brand new so I don't know if I am doing something wrong? I followed the instructions thoroughly.


Welcome to fixya\012\012Hello\012\012 \012\012I have a solution for this ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Just rec'd product...glazed sealed ceramic floors throughout home...followed instructions and washed all covers by themselves...have now mopped SAME area 4 times and still have DULL, STREAKY finish! PLEASE HELP...have washed floors (home is 1-y-o) prior to this on hands and knees with TILER'S SPONGES that have been SUPERB...was hoping to save my knees...but your mop is simply NOT doing the job yet...what am i doing wrong?


Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I tried to register the bonus submersible handset following the instructions on the owner's manual yet registrations failed luz croucher of Whangarei


... Vacuums

My electrolux stick vac EL 1000 suddenly doesn't even light up to show it's charging! Is it a battery? A wire? As I try different outlets it will light up momentarily and then go out.... What do you think?


Had the same problem with 3 of my vacuums, tried using my rc charger and it fixed the problem. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

I have an Emerald 203/183 sewing machine and am having trouble changing the bobbin. I have tried to follow the instructions but to no avail. The lower thread keeps bunching up.


... Vacuums

Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!


Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum

Poor cleaning I recently bought the Shark Steam Mop as I read mainly fantastic reviews. I was disappointed to find that it leaves a slight film on my dark hardwood floors when finished. I can wipe the film away with my finger and you can see foot prints if walked over. I also found that there are cloth streaks on my ceramic floors after drying as well. I followed all instructions, vacuumed beforehand, used distilled water even though my water is not considered hard, cleaned slowly, etc. I am wo


Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Cleaning I cannot get the cleaner to release solution on carpet. have lost manual. is there a trick to this? I have tried squeezing trigger handle to dispense solution with no luck. have followed instructions (2 capfuls cleaner, fill with hot water to fill line) on filling tank.


Either you have a pinched or clogged water line, or the rod in the handle is pushing down like it should. The drw back is Bissell has deemed this unit and its parts obsolete. So any parts are hard to find.\015\012\015\012 ... Bissell 1950-3 Quicksteamer Plus Vacuum

Hi My Hoover wind tunnel cyclonic stopped working when i was using it. I tried different plug even then it doesnt work . What to do??


If the motor stopped running, it most likely did because it was not being cooled, becuause something was stopping up the air flow. If you have cleaned the secondary filter out and it still stops while running, then remove the exhaust filter cartridg ... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

Battery replacement I tried to follow the owner's manual instructions, but I have been unable to remove the battery cover.


I have opened CHV1400 by removing two screws that are visible when you remove the "accessory" from its holder (located underside of the vacuum). After removing the 2 screws, I had to pull the green colored part by exerting slight force. You will now ... Black & Decker CHV1400 Bagless Handheld Cyclonic Vacuum

Hi I have a new sunbeam Eskimo ice maker I have had it on now for 3 hrs approx the water is cold and i have it on the med size blocks its only bringing down 4 ice blocks in the 3 hr period is that normal as its not doing much else i have tried to switch it off and on again and is not making any difference i have been watching and waiting and follpowed instruction booklet to the letter so why am i not getting lots of ice blocks as i said water is nice and cold.


Sorry to read about your problem, I hope this helps you out.yesI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Sunbeam Vacuums

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little


Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0658 seconds