Having problems with your Thermax Vacuums ?

How can I remove the bottom from my Thermax AF1

Answers :

Repair Help & Product Troubleshooting for Thermax Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How can I remove the bottom from my Thermax AF1

... Thermax Vacuums

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that

Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.

The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.

Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Remove bottom of cover on vacuum bottom. Making a

On this model, the bottom does not come off but the top does. on the top hood there are 2 latches to turn with a screwdriver and the hood will come off. ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.

HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole

Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.

If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

I am triing to remove the top part of a g1 sebo upright from the bottom half so i can remove the cover

... Sebo Essential G1 Upright Vacuum Cleaner

Wish to remove bottom ofpowerhead-Kenmore Progressive 11629912990

I\015\012have a whispertone vacuum, different model #, but maybe instructions\015\012will be the same. Turns out I didn't need a new belt, just clean out\015\012the crud and reset overload protector. The instructions in the manual\015\012tell you to ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Can you remove the plastic part on the bottom of the bag or to tighten or is that a crack I see dust blows out of the bottom

There is a hand grip built into the bottom of the housing to help remove it. If it has not been removed on a regular basis to dump out heavy debris, it may be stuck. Use a screwdriver as a lever and pry it outward from the motor unit to remove it and ... Kirby Ultimate G Bagged Upright Vacuum

We have A "WC1000" 12 cup Coffee maker. It is leaking water out the bottom of the unit. We have removed the bottom metal plate, but there is nothing in that area requiring attention.

I think a gasket may have melted, or is leaking. Also check the ends of the little hoses. they may have cracked. ... Vacuums

I removed the brush from bottom of the vacuum to remove hair from the bristles. When I re-assembled the vacuum, there was no longer suction. Also, the vacuum no longer stands upright when not in use. It's like something is blocking the upright portion from locking.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off

I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums

Need to remove bottom cover of Panasonic MCV7314 vacuum to see if the belt is broken. I can't figure out how to remove and can't find a manual online.

I did a search for the manual for that model and found a pdf file online that had instructions and pictures. It was still slightly different and hard to get off. I took out two screws and then held in two side "clips" and wrestled it off. I dont t ... Panasonic Vacuums

I need the manual for thermax AFvacuum - Thermax AF1 Canister Vacuum

Please go to this web site to request an owners manual.\015\012\015\012http://www.thermaxaf.com/ ... Thermax AF1 Canister Vacuum

Replace broken belt on a Hoover Elite Rewind. Removed bottom panel, how do I remove brush to put on new belt?

I have the agitator belt style 190 for the Hoover elite rewind I put it on and the belt broke again what do I do help carpet needs cleaning. ... Hoover Elite Rewind Bagless Upright VacuumVacuum

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?

... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.

Its still clogged, you gotta dig deeper ... Vacuums

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.

Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

The little movable fin on the bottom of the removable collection fin broke off when I was removing the fin from the unit to clean the IONIC BREEZE QUANDRA AIR PURIFYER.

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0513 seconds